20 Most Recent Whirlpool LER6636PW Electric Dryer - Page 3 Questions & Answers

The orange glow is the heating element. The smell is the Phenolic Resin in the circuit boards. My dad worked for 20 years at the factory where the board material was made. It has a distinctive fishy smell. It should all settle down. Just make sure the vent pipe is as short as possible, there are no kinks and that the flap on the outside wall opens properly. There are three temperature safety devices in all dryers, thermostat, high limit thermostat and thermal cut out.

The breakers could had tripped or there could be a fuse that has blown on your dryer or the start switch or the door switch is bad or the motor is not working for the dryer.You will have to call a repair person to see what the problem is with the dryer.

The capacity of the Whirlpool Duet GHW9300PW4 front-loading washing machine is approximately 4.3 cubic feet. This is a standard capacity for a front-loading washing machine, and it should be sufficient for most households. It is always a good idea to refer to the manufacturer's specifications or the manual for your specific model of washing machine to get the most accurate information on capacity and other features. I hope this information is helpful. Let me know if you have any other questions or if there is anything else I can assist with.

possible bearings--bent or damaged bracket --out of level

It is a Control board issue. Videos and articles. https://www.google.com/search?q=Whirlpool+dryer+WED9600TW+code+F01 ..

This is a combined Washer and Dryer? Is it moisture sensing? If it is, you need a new sensor.

Hi, please power cycle your dryer and check for the error again. Ensure that your the lint has been cleaned out of your dryer before checking for the error again. If still having issues, please check any initial document that has tips/trouble section to help overcome that specific error. Thank you.

That is annoying and it happened to me on a GE Debra. Pull the oven out and you should see a small panel where the rear of the element is. Remove it, normally just 2 screws. There will also be fibreglass insulation, but just move it to one side.

I would not be surprised if there's a loose bit of steel somewhere near the heater element. Current in the heater generates an alternating magnetic field that could act on the loose steel. A more likely possibility is that you have a loose contact on the heater element, and what you hear as rattling is actually sparking. This is fairly common, and can cause severe heat damage to the insulation on the wiring going to the heater element. I've seen the terminals on the heater burned off by the arcing. Check that out ASAP. If you get it soon enough, you may be able to fix the problem by cleaning up the male terminal on the heater and (if the wiring is still good), cleaning and slightly tightening the grip on the female terminal. If the wire insulation is damaged, trim the wire back to undamaged insulation and crimp on a new high-temperature rated terminal.

Yes they are both the same. https://www.google.com/search?q=Can+I+put+a+250v+cord+on+a+240v+whirlpool+dryer ..

Fridges and Freezers are measured in cubic feet, dryers tend to be graded by weight of damp clothing in pounds.

Large Capacity Dryers - Whirlpool

https://www.whirlpool.com > blog > washers-and-dryers Most standard dryers offer between 5.0 and 7.0 cubic feet of capacity. To help translate cubic footage into real-life laundry loads, consider that a 7.0 cu. ft. Or you can calculate it.

Whirlpool 29-inch Electric Dryer LEQ9508PW0 Drum Capacity

Dryer Drum Capacity as per Manufacturer Specifications (in cubic feet): The manufacturers began using cubic feet capacity numbers only recently. Previously, they used relative terms such as "Large" or "Extra Capacity" or laundry weight (e.g. "16 lbs per load") which did not take into account different fabric weight and volume. Even dryers available today do not have capacity written in the manual because the same manual can be used across multiple models. Once the model is no longer sold, the sales literature is discarded and capacity information often lost. Analyzing dryers and their components, searching through old technical information and sales literature, and determining their capacity is a labor intensive and time-consuming task and we are far from finished. A small charge will help us continue our research. Consider this: if you were to spend more than few minutes looking for dryer capacity on the internet, you would be earning LESS than minimum wage. Get LEQ9508PW0 Drum Capacity ($0.99) Calculate Electric Dryer Drum capacity This is a geometric method to calculate drum capacity based on the cylinder volume formula. Unfortunately, the value could be as much as 25% off from the manufacturer stated capacity. Why? Because a drum is not exactly a cylinder. The edge where bottom connected to the wall is not at 90 degree angle but smooth and rounded. The end of the drum is not clearly marked and the back is not always flat. Finally, there are baffles inside the drum used for tumbling clothes. This method can be used as a crude estimate but we do not recommend using it for comparisson when shopping for a new dryer. To determine your electric dryer drum capacity please take two simple measurements: 1. Use the ruler to measure the depth of the drum (indicated by the red line on the diagram) 2. Now find the distance across the drum, the diameter (the green line on the diagram). Do not confuse the size of the the door opening with the size of the drum. In this case make the measurements INSIDE the drum. Solution: Dryer Drum Depth: in. Dryer Drum Diameter: in. Calculate Drum Capacity

Question edited for clarity, correct order. I can't find the capacity of the drum, but here are the dimensions. https://partselectcom.azureedge.net//assets/manuals/05CE51E03B4DD72F710357284D5FCEE8A8EC3D12.pdf There is a free calculator here based on diameter and depth. https://www.allrepairmanuals.com/whirlpool-gas-dryer.htm?model_number=LGR4634JQ3 https://www.google.com/search?q=whirlpool+%22LGR4634JQ3%22+dryer+drum+capacity ..

Is the air blowing from the exhaust in the back of the dryer and are clothes drying? if the motor turned the other way, you would have no air flow. The dryer is working as designed. Also, if the drum turned clockwise, the idler pulley would not keep the belt tight. Some dryers turn clockwise, some counterclockwise.

The elements are usually not interchangeable. You can use a website like appliance parts pro to look up both units by model number to see what the elements look like. They usually have diffferent mounting hardware or the enclosure might be different, some mount to the back wall and others mount underneath the drum.

Hi, Please unplug the washing machine for 5 minutes before adding back the plug in order to power it on again and start it. If it still does not start, please check that the lint tray is empty and your clothes are evenly distributed. Another method is to turn the cycle dial counter-clockwise 90 degrees before attempting to set the cycle again. Thank you.

Hi, Please make sure that you've removed all of the lint from your dryer prior to every cycle. Next, try to see if the varying the load size effects whether your clothes are heated or not. If all else fails, please schedule an inspection by Whirlpool by calling 1 (866) 698-2538. Thank you.

Hi, It sounds like there is a hole in your machine. Please check any pipes for tears and any unintended holes within your dryer. Thank you.

call mfg

Check for a break in the wires the sensor my not be reviewing the signal if the wire is broken sometimes the wire could be broke internally and not visually noticeable check with a voltage meter for continuity from the sensor to the board

squeaky belt or bearings in tub