Weber Baby Q Grill - Answered Questions & Fixed issues

Don't worry, you'll be grilling in no time, if you follow these instructions:

1. Turn the gas tank valve OFF.

2. Disconnect the grill's hose from the propane tank and wait 5 minutes.

3. Reconnect the hose to the tank and open the tank's gas valve VERY, VERY SLOWLY (Slow Motion, slow).

Once the valve is fully open light one burner and turn it to HIGH. Has the flame height returned to normal? If so, light the remaining burner and turn it to HIGH. Do both flame heights look normal?
If so, you solve the problem! Remember to always turn the tank valve ON Very, Very Slowly.

Hope this helped you. Please let me know and Happy Grilling!!

Try Amazon or a local outdoor furnishings store.

Sounds like the reg is letting too much gas pass

Clean out the burner holes with a nail.

Sounds like you need to replace the igniter. If the gas lights with a match, there's nothing wrong with the gas bottle. line or burner.

if you got the cannister from the shop with the grill the chances are that the cannister needs filling first as gas bottles are empty when new.

No , burner needs cleaning and the orrfice

Google it should come up on the wed site and you can down load it .

Weber has the manuals to many of their grills on their support page: http://help.weber.com/manuals/default.aspx#model . You'll need to use the drop-down menus to select your region, language, Gas, Weber Q Grill and then the model number. If you can read the serial number of your grill, you can get to the manual more quickly from the Serial Number tab, http://help.weber.com/manuals/default.aspx#serial-number . The direct link to the Weber Baby Q (2008) owner's manual is http://c929377.r77.cf2.rackcdn.com/BabyQ_OwnersGuide_41636_060205.pdf . Other useful documents are also available from the site. I hope this helps. Cindy Wells

Hi maggiezmartA venturi valve is a valve that has a reduced size in the middle thus causing a low pressure in the middle of the valve to create a vacuum to pull liquids/gases into the flow stream.More information can be had at the following webpagePlease take time to rate meBudhttp://en.wikipedia.org/wiki/Venturi_effect

You can try replacing the regulator to cure the gas flow problem, I believe the ignition is a piezo, if it does not click when you push it or turn it, it most likely needs to be replaced. If it still clicks, then there could be a bad wire or electrode.

Check there is gas at the burners and that the orfices are not block or the burners are bot blocked .Turn on burners let pressure out of line turn off tank remove gas line then reconnect to tank and turn on tank slowly see if this works

Sounds like you may have a bad regulator, try replacing it.

High is the highest and hottest setting/temperature. Depending on how long you preheat the gill with the lid close, will determine what the maximum temperature will be.If it's not heating well, the burners may need to be removed and cleaned. The link below is for the Baby Q Model. Pay particular attention to the Annual Maintenance Section, as it will show you how to remove the burner(s) and clean them.

http://help.weber.com/manuals/pdf_files_2011/Gas/Weber%20Q/BabyQ_OwnersGuide_41636_060205.pdf

I hope this helps you and Thanks for choosing FixYa. Happy Grilling!!

Whether using a gas canister or a tank, To solve this problem, first be sure you have adequate gas in the tank. If that checks out OK, do the following:

1. Turn the gas tank valve OFF and disconnect the hose from the tank. Or remove the canister from
it's holder.

2. Wait 5 minutes and reconnect the hose to the tank. Or reinstall the canister into the holder.

3. Open the tank valve or canister valve VERY, VERY SLOWLY (Slow motion, slow).

4. Once the tank valve is fully open, light the burner and set the burner
control knob on HIGH. Does the flame height look correct for being set on HIGH? If so, light
any remaining burners the same way. Do all the burner flames look correct? If so, you solved
the problem. Remember, to always open the tank valve Very, Very Slowly.

Hope this helped you and thanks for choosing FixYa. Happy Grilling!!

Whether using a gas canister or a tank, To solve this problem, first be sure you have adequate gas in the tank. If that checks out OK, do the following:

1. Turn the gas tank valve OFF and disconnect the hose from the tank. Or remove the canister from
it's holder.

2. Wait 5 minutes and reconnect the hose to the tank. Or reinstall the canister into the holder.

3. Open the tank valve or canister valve VERY, VERY SLOWLY (Slow motion, slow).

4. Once the tank valve is fully open, light the burner and set the burner
control knob on HIGH. Does the flame height look correct for being set on HIGH? If so, light
any remaining burners the same way. Do all the burner flames look correct? If so, you solved
the problem. Remember, to always open the tank valve Very, Very Slowly.

Hope this helped you and thanks for choosing FixYa. Happy Grilling!!

Here's a link to the tank hose adapter/regulator you're looking for. However, they are currently out of stock, but have more on order. I suggest that you place an order as soon as you can.

http://www.appliancefactoryparts.com/search/partinfo.php?partsID=493146&modelsID=&typeName=gas%20grill

Hope this helps you and Happy Grilling!!

You will need to replace the control knob assembly. Which includes the tank hook up & regulator. Contact Weber Customer Service @ 1-800-446-1071 for this part.

Hope this helped you.

Unscrew the push button battery cap and you will find the old battery sitting in the battery holder.
Take note of which way the old battery is facing and install the new one in the same direction. It's also a good idea to check for any corrosion on the terminals of the battery holder. before installing the new battery. If you see any, a Q-Tip and WD40 will do a good job in removing it.

Hope this helped you and Happy Grilling!!

When a hamburger is cooked to 160 °F as measured with a food thermometer, it is both safe and delicious!