20 Most Recent
Samsung LE40R73BD 40 in. HD-Ready LCD Television - Page 8 Questions & Answers
My samsung le40r7 tv dont turn on any more i bought it 3 years
Hi I am vortash .. there is a modification kit available for this tv and available from ebay priced about $50 0r £30 depending on your location . It is the start up driver circuit that needs these components on the power supply if you are competant to attempt this .However if not then I suggest that you take it to a local enginner for a free estimate he will at least be able to tell you the fault . regards Vortash
6/20/2010 4:38:20 PM •
Samsung...
•
Answered
on Jun 20, 2010
Problem switching on and off
samsung will do a free repair i had the same fault and they fixed it fir free give them (SAMSUNG) a call.it is a known fault
6/20/2010 4:26:22 PM •
Samsung...
•
Answered
on Jun 20, 2010
My Samsung LCD wont turn on
samsung will fix it free of charge .i had the same fault with mine it is 3-4 years old .phoned samsung and they fixed it for free
6/20/2010 4:21:52 PM •
Samsung...
•
Answered
on Jun 20, 2010
My Samsung LE40R73BD 40 in. HDTV-Ready LCD
Are you convinced that all cables are correctly connected, also to the electricity. The scart cable(s) are properly in place.
Try to turn the TV off the next time it shows a mind of its own. Disconnect it from the electricity, turn off any extra units that could be attatched to it. Let the TV rest for ,2-10 minutes suit my appliances well. Then start with cables and connections in reverse order. This has oftrn worked for me I havebecome more patient as the years goby.
6/16/2010 4:14:31 PM •
Samsung...
•
Answered
on Jun 16, 2010
I have no color on my Samsung Flatscreen TV
Hello,
This means absolutely no color - equivalent to a black and white picture. Not even a hint of color.
First, confirm that the source is actually in color - try another channel or input device.
Next, check the settings of the color control - it may have accidentally been turned down. If your TV has some kind of automatic picture mode, try turning if off and adjusting the color control. Try adjusting fine tuning if you have such a control and the problem is with a broadcast or cable transmission.
At this point with a confirmed color signal source, there is a problem with the chroma circuitry.
Note that to the average person, the obvious question becomes: is my color picture tube bad? The answer is a definitive NO. It is virtually impossible for a defective CRT to cause a total loss of color. A defective CRT can cause a lack of a primary color - R, G, or, B or a short between two colors which will mess up the color but is not likely to result in a black and white picture.
Some possibilities in no particular order:
Weak signal or defect in tuner/IF causing loss of signal strength.
Coler killer set too high (internal control) if it has one.
Defective part around the chroma chip/circuit. Faulty color oscillator.
Bad connections in area of chroma chip/circuit.
Defective chroma chip (don't suspect this first just because it is probably very expensive).
Try prodding the main board around the chroma chip with an insulated tool to see if you can make the color come and go.
I had one set where a $.02 resistor decided to open up causing just this problem - perfect BW picture, no color. Another had a coil with a broken wire.
6/16/2010 1:33:04 AM •
Samsung...
•
Answered
on Jun 16, 2010
Screen keeps going black audio still working
Hello,
you can fix this by opening the back cover of the television to check for cold soldering, if found you can solder if you have the skill to that , but it doesn't still work.
More than likely this will be down to your Y Sustain board has gone faulty, when the back is off your TV it is on the left hand side and will probably have a fuse that has blown, replacing the fuse will not solve the problem as it is the IMP under the heatsink that has gone faulty.
You should get the part number of the board and Google or Ebay for a replacement.
Hope this help
6/14/2010 12:11:08 PM •
Samsung...
•
Answered
on Jun 14, 2010
Sound no picture
Hello,
Try connecting TV to cable direct also try unplugging both converter and TV for wile like 5 mins plug both back in see if TV and converter sync.
But if it still doesn't work...
More than likely this will be down to your Y Sustain board has gone faulty, when the back is off your TV it is on the left hand side and will probably have a fuse that has blown, replacing the fuse will not solve the problem as it is the IMP under the heatsink that has gone faulty.
You should get the part number of the board and Google or Ebay for a replacement.
Hope this help
6/14/2010 12:08:04 PM •
Samsung...
•
Answered
on Jun 14, 2010
My samsung le40r73bd tv has developed a fault the
there is a problem on your inverter board and the cold cathode lamp.The inverter board is the supplying high voltage supply to the cold cathode lamp.This cold cathode lamp is the illuminating the screen in which the the picture will appear once cold cathode is lit.here is a link where you can buy the parts..
Normal
0
MicrosoftInternetExplorer4
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";}
- http://s807.photobucket.com/albums/yy352/budm/Bad%20backlight%20lamp/
- http://s807.photobucket.com/home/budm/allalbums
:Good luck hope this helps you..
please rate my help
6/14/2010 10:34:38 AM •
Samsung...
•
Answered
on Jun 14, 2010
Samsung LE40R
try to change the stantard from the channel setting menu(bg-dk etc.)
6/6/2010 1:55:27 PM •
Samsung...
•
Answered
on Jun 06, 2010
How do i reset my tv to factory settings
Your particular TV does not appear to have a "reset" mode to return to default (factory) settings. I can only assume that you are trying to get the picture back to "normal".
To do this grab your remote, press the "menu" button then select "picture' using the up and down buttons. Then press "enter" again and select "mode" this is where you can change the size, aspect ratio and etc. of your picture. Use the up and down buttons to select 16 by 9 format or "standard" if it says that in the menu. The image I have is too small for me to read exactly which setting it should be at. At least this is where you change those options I am pretty sure you will know which setting by checking the video. If it's still wrong then try some of the other "modes" and check again.
Zashiban
5/31/2010 6:34:04 PM •
Samsung...
•
Answered
on May 31, 2010
Picture went dead
More than likely your backlight inverter board went dead
5/30/2010 6:18:10 PM •
Samsung...
•
Answered
on May 30, 2010
Samsung LE40R73 LCD clicking
The power supply pcb located in the centre of the panel has 4 capacitors on the pcb that go faulty. This can be seen by the tops on them bulging up with possible brown fluid discharge. The value of these is 1000uF and after replacing these (can be purchased from Maplins or any other electronic components outlet), the fault will be cured.
Not finding what you are looking for?