20 Most Recent OKI MICROLINE® 390 FB Printer - Page 5 Questions & Answers

You will find the waste toner auger (Coiled wire in the plastic tube) is either snapped or blocked with hard toner. Its simple to remove as it just unscrews. If I remember correctly it sits under the transfer belt and runs down the back and right side of the base. Anyway clean and inspect it as that is what removes the waste toner.

Your error refers to the ROS motor in the laser unit. Now this means a new ROS Assy (Laser/Scanner) is needed, however if you are technically minded, remove the assy and open it. You will see a spinning mirror. Remove it and clean its shaft and oil with with a very very light oil (Model train oil). reassemble and clean the fixed and spinning mirrors, if it works great and if it does not get some money from the bank and by a new printer. The part number for the ROS is : 062K11210 good luck. Good luck

it means FUSER MOTOR LOCK ERROR call a tech or you could try replacing the fuser motor

480 is not listed in any OKI manual. However the closest to it refers to paper size mismatch. Check your driver setting especially paper size. If in UK make sure its set to A4. if in USA then yours is letter size.

Check that the toner cartridge is for your model. Think you have wrong type.

https://printcopy.info/?l=en&mod=erc&brand=OKI&model=CX3641 http://www.fixya.com/support/t896904-power_off_fatal_error_917 http://www.fixya.com/support/t1502883-fatal_error_917_oki_c9600_printer OKI CX3641 Error Codes List page 1 from 11

There are 3 competing controls. 1) Software 2) Printer driver 3) Front panel. Software control overrides printer driver. Printer driver overrides front panel. Your software settings therefore dominate. That said, you can choose to have the front panel settings "dominate." Those front panel settings may enable you to change margin widths. Even though this may be possible, you may well find the solution is within the invoice software's print setup where you may have to check some box to enable 11 inch printing or whatever is required. But that requires knowledge of the invoice software program. I am unable to determine if you are encountering a sudden failure of a system previously working. If this is a printer failure rather than a software configuration problem, you will have to check the okidata help. Here is some reference material: Okidata Users Manual ML320 ML321 Turbo Problem 1 My word processor files...

They probably changed the setting in your operating system. Do you have windows or apple? Beyond that, do you recall if they made this change at the store on the printer itself, or were they tinkering with your PC when they made it monochrome?

There's a small fuse in the drum that blows when it's first powered up after changing the drum. You can emulate a small fuse with an analog VOM set on Amps. With printer OFF, using a light wire like phone wire, connect the VOM to the drum terminals. When you power up, in a few seconds you'll see the VOM needle bounce one way or the other (doesn't matter). The moment you see that, pull the connection from the VOM. You've just impersonated a small fuse blowing. Here's an article on how to make that connection to the drum: http://www.fixya.com/support/t8952601-reset_drum_life_oki_c3400

Open the machine and remove the paper tray, the drum tray, the transfer belt and the fuser. Check all for a sheet or part sheet of paper. replace all and retry.If still register a paper jam have a look underneath to see if one of the paper pick up sensors is jammed open.

There is a sensor that detects the presence of the cartridge and also a chip reader attached to the LED scanners. First trick is to check the chip. Older machines often become less able to read after market chips. Locate the slot in the side of the cartridge at the end away from the locking mechanism. Carefully prise the cover off and slide out the RF chip inside the recess. Tape this on to the top of the cartridge directly above the recess. Put it back in the printer. and try it. This puts the chip closer to the chip reader and often fixes the recognition problem. A faulty sensor is more difficult to fix and would need a service technician who is more likely to recommend replacing the machine.

This should have everything you need. First of course - get an new fuser from you Oki agent. http://www.fortwayneprinterrepair.com/wordpress/2015/01/05/okidata-c610-c711-fuser-replacement-44289101/

I am David, and I do not have one, and I cannot get one for you. Try a store where they sell them, or go online at Amazon or E-bay. God bless your efforts.