Top 20 OKI MICROLINE® 390 FB Printer Questions & Answers

Dot matrix printheads go bad, can be rebuilt, never had great luck cleaning, pins get stuck out.. Also there is a lever that moves the printhead closer or farther from paper. make sure that is in the right position. Usually on top cover may have numbers by the lever such as 1 , 2 , 3 etc

There are a few things that are possibly wrong with your printer. You may want to try completely unplugging and reinserting the cord into the power outlet. If that doesn't work, check your printers ink levels and ensure that there is no paper jam. Best of luck.

try here:

Seneca Data Phone: 800-444-4060 Fax: 315-433-0945 Hours: Mon - Fri: 8am - 7 pm ET Web Site: http://agson.senecadata.com Notes: Net terms, same day shipment, online ordering, account and order status.

you can download the drivers from the below site........
http://www.howtodrivers.com/model534258.html
dont forget to rate the solution
have a nice day

http://www.oki.com/ driver download from this website

try these links for a user manual: ML1190eco User Guides Manuals http://www.manuals365.com/oki/ml11uen2_tcm3-45862-manuals365.html

I have this manual for you on page 37 for changing font. https://files.support.epson.com/pdf/fx890_/fx890_u1.pdf

use the HP laserjet 4 or 4000 print driver. this is the most basic print driver and has played nicely with the older printers

have you checked the wall socket , try another wall socket , try another power cord ,and check if all is switched on

here is the user manual, is that the same as the service manual? http://www.primoit.co.uk/pdf/06E20B7E-AC7E-4E84-BA06-D1DD86563306.pdf

replace cartridges for $$$$ or toss printer as OKI stopped making printer 3-4 years ago.

Hi, I believe that this is a high-temperature error. so, you might need to move the printer to a cooler room or lower the temperature of the room that the printer is in. Thank you.

There could be a few possible reasons why your Okidata Microline 280 Eco printer is jumping around 0.75" for each new page. Here are some things to check:

1. Check the paper feed mechanism: Make sure the paper is feeding correctly through the printer and that the paper guide is properly aligned. If the paper is not being fed correctly, it can cause the printer to jump around.
2. Check the tractor feed mechanism: The tractor feed mechanism may not be gripping the paper correctly, causing it to feed inconsistently. Make sure the tractor feed mechanism is properly aligned and tightened.
3. Check the page length settings: Double-check that the page length settings are correct and that they match the size of the paper you are using. If the settings are incorrect, the printer may not be able to print the entire page and may skip to the next page prematurely.
4. Check the top of form settings: Make sure the top of form is set correctly and is not too close to the top of the page. If it is too close, it may cause the printer to jump around.
5. Check the print head alignment: If the print head is not aligned correctly, it can cause the printer to jump around. Check the print head alignment and adjust it if necessary.

If none of these steps resolve the issue, it may be a hardware problem with the printer itself. In that case, you may need to contact Okidata technical support for further assistance or consider taking the printer to a professional repair shop.

The exposure lamp is dirty and needs to clean on all surfaces. if not fixed then you need to replace the lamp.

Check the cyan developer unit and cyan drum.

This is the only place it is mentioned is the Service Manual and the Error codes list https://www.manualslib.com/manual/869465/Oki-C9600.html?page=253&term=RFID&selected=5#manual Use the Search feature for 'RFID'.

C9600/C9800/ES3640 Error Codes - OKI Support

https://my.okidata.com > idocs2.nsf PDF May 24, 2005 - Access failure to parameter storage location due to file damage or etc. ... An interface error was detected with the RFID reader device. 4 pages

The OKI replacement drum explains how to reset the timer in the paperwork that comes with the drum.

https://www.google.com/search?q=Error+182+call+service+OKI+B432+DN https://printcopy.info/index.php?l=en&mod=erc&brand=OKI&model=B432dn&code=182 This what OKI U.K. says Service Call 181: Error 182: Error 183: Error 184: Error 185: Error Option unit I/F error (181 = Duplex Unit. 182, 183, 184, 185 = Optional Tray) Does this error recur? Yes Restore the power. Check to make sure the contact points of the connector and replace the optional unit

Unplug the machine. Pull the machine out. Remove all the paper trays. Open all the doors. Remove the Toner. Get a flashlight and look for a small piece of torn paper from a previous jam that was torn when pulled out. Clean the rubber feed rollers with a damp soapy cloth, rinse and leave to dry. Reassemble the machine. Put in new paper from an unopened pack as paper can get damp this time of year. Reconnect power. Try again. https://www.google.com/search?q=OKI+MC352+paper+jam ..

This is what Oki says regarding that issue.

Troubleshooting ' OKI

https://www.oki.com > printing > contents > contents Nothing is displayed on the display screen after turning the machine on. ... The output port of the printer driver is incorrect. Specify the output port for ...