Philips 50PFP5332D 50 in. Plasma Television - Answered Questions & Fixed issues

bad power circuit may cause such problems. may be power ic or bad capacitors.....

Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electro-medical.blogspot.com/ http://homenol.blogspot.com/ http://electronicshelponline.blogspot.com/ If blinks continue without any pause, the main board is faulty. Search the site by type in the "brand name" to your device, in the "Search box at the top right of the display window of the Homepage" to get gathered related posts. Counting of number of blinks to Philips TVs is entirely different to that of other brand TVs. It is not a direct count procedure. The site have details about how to count the number of LED blinks [Fault Codes] to Philips brand TVs are given; along with details of the faulty circuit location.

It sounds like you have a problem were the Y sus/buffers board (the one on the left ) has issues with the connectors to the screen need unpluging cleaning and putting back

If you wish to get some details; visit the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/

its the capacitor inside the tv open it up and you should see atleast 1 capacitor which has bulged ( looks like glue coming out of it ) usually a 3000 ~ you can replace these yourself no problem for around 10p each but i do warn you there is a chance you could lose your built in freeview in doing so!

Well if the power supply board alone is making the same then clearly the problem is in it. I can't tell you remotely what makes the noise and why is it shutting down. I've seen them make noise because of a shorted diode in the PFC circuit, because of a failed capacitor in the Vs or standby circuit, because of a cracked solder joint in some of the large transformers or because of a worn out filter capacitors. Oh, and because of a failing thermistor at the board's input, but that's usually accompanied with smoke and is easy to detect, plus it only happens once or at most twice. If course it may as well be something else. The best I can do is offer you to send the board to us for inspection and repair. This should be the board and the repair service we offer for it: http://www.coppelltvrepair.com/p/215/lj92-01511a-996510019427-power-supply-board-philips-50pfp5332d-service-repair Hope that helps!

The experience I have seen with this model is on the power supply module, near the lower center of the board, check for two swollen 3300Mfd 10V capacitors, change these two parts and you might correct the issue. The board is perhaps part number LJ44-00108.

No place to put your RGB on the PC or on the TV? Your TV should have an RGB port for sure. The "green" may be yellow instead.
Your PC will need a video card installed that features a RGB output to make it work from there.
Some PCs use DVI out instead. You would then need a DVI/HDMI converter to plug into your TV's HDMI port and then to the PC.

Go into tv menu and do reset. That is if you want to reset every thing. i'm not sure what you think rebooting is?

hi, capacitors, they usually swell up or a shorted diode/ transistor and may be a bad dry solder joint, good luck with the repair regards shaun

Sounds like a power board has blown inside the set. Take it to a repair shop.

If you wish to get some details; check the site linked here. Viewing it in "Mosaic" will make surf easy. http://electronicshelponline.blogspot.com/

Main board is likely to be faulty. Contact the authorized service center for Philips. This is not a user reparable fault. So many adjustments are there, after the main board repair/replacement. If you wish to get some details, check the site linked here. Pull up older posts. Check the site in 'Mosaic' view. It will make search easy. http://electronicshelponline.blogspot.com/

Look for the digital audio out port on the TV. It has a rubber plug covering it to keep dirt out. remove that plug and connect the sound bar.

Plasmas are notorious for a slight humming or buzz that emits when they are on... A clicking sound when plugged in isn't nececessarily bad. However, the picture not working is bad and this may require a technician. Are you using the proper power cord that came with your tv? Are you able to use the included remote or use the power buttons on the television itself? Has the tv been moved or dropped recently?

There are several possibilities here.If the picture is very dark and blotchy you may have a bad X-MAIN (ZSUS) board.It can also be the Y-Main board, but less likely, it usually fails in a different way. Here are a few useful repairs for your TV we offer: http://www.coppelltvrepair.com/search?Q=50PFP5332D&As=false&Pf=&Pt=&Sid=false&btnsearch=Search (Basically just a search of the TV model at the site to see what it comes up with) Hope it helps!

Philips 50 inch plasma tv no video but has sound

These blinks are fault indication, and known as blinking codes. From the number of blinks occur at one time switch ON; you can get an idea about the faulty circuit stage inside the TV. This will make repair easy. For more information, check the link http://electronicshelponline.blogspot.com/

Let it be. It's a good practice. Keep an other Hair Dryer. It will be best for you I assumes. Can you troubleshoot its main power supply regulator board. If so, google.com/+GopakumarGopalan check this link, and come over to me.

Very difficult to predict, what might be the fault to your Philips TV. It will be best to contact the authorized service center for Philips. google.com/+GopakumarGopalan