Top 20
Kyocera FS-3900DN Laser Printer Questions & Answers
Laser jet printer
call service 74101:0071621
Error 7410 is drum unit not installed properly if you open the side door and push the the drum unit back in to place it probably just popped out of position a little bit
4/11/2015 2:32:23 AM •
Kyocera...
•
78 views • 0 helpful votes
Kyocera service code 7410:0013781
Drum unit non- installing error The drum unit is not installed or not installed properly. The drum PWB EEPROM does not communicate normally.
3/6/2015 6:06:21 AM •
Kyocera...
•
140 views • 0 helpful votes
Prints black background, white letters
sounds like invers is turned on which switches everything black will be white and white will be black try to find this seting and turn it off
8/1/2014 9:17:23 AM •
Kyocera...
•
876 views • 0 helpful votes
Triumph-adler DC 2018 error C6000
Defective Fixing Unit... Poor contact in the thermistor connector terminals, bad thermistor, broken heater lamp wire or some other contact problem related to fixing section. If it is possible, check with another Fixing Unit.
5/2/2014 10:35:45 AM •
Kyocera...
•
2,152 views • 1 helpful votes
Command center admin user
are you asking for the password the default passwords are either Admin or admin00 that is for the web page on the machine its usally Admin or the speed of the mACHINE PLUSE TWO zeros
4/22/2014 11:37:09 AM •
Kyocera...
•
901 views • 0 helpful votes
PRINTER IS PRINTING BLACK PAGES AND WHITE CHARACTERS
It might be the main charger (MC-310 or MC-320) or the ground of the developer unit. In the first case, just remove the roller from the drum unit and clean it. In the second case, you have to remove the engine pwb (the board under the printer) and check the spring which grounds the developer unit.
7/14/2014 4:03:43 PM •
Kyocera...
•
64 views • 0 helpful votes
7410 : 0674421
Open the left cover and push the drum unit inside (above the waste toner bottle) to lock. You will hear a sound like "click". If you cannot push the drum unit, you can first remove the developer unit.
7/18/2014 1:40:46 PM •
Kyocera...
•
37 views • 0 helpful votes
7410: 0178137
Power off the printer, open left door and press in the drum unit (press in the area just above the square button) until it clicks into place. Close the door and power on.
6/30/2014 8:24:27 AM •
Kyocera...
•
53 views • 0 helpful votes
7410:0006643
Power the printer off. Open left door and push in on drum unit until it clicks into place. Power the printer back on and the code should be cleared.
4/9/2014 2:32:17 AM •
Kyocera...
•
157 views • 2 helpful votes
Dark lines fs 3900
The lines are more than likely caused by either the Drum, Developer or Fuser unit. I have found in many cases that if non genuine toner is being used this will give you poor quality images. You can try using genuine toner which may resolve your issue but you may have to run a few hundred prints to clear out the old toner before the image improves.
4/15/2014 4:07:25 PM •
Kyocera...
•
122 views • 0 helpful votes
Error code 7410:0096907
Here is a link where you can download the documentation for your printer. Click on the link for your model, then the "documentation" tab. Then download what you want from there. Hope this helps.
http://www.kyoceradocumentsolutions.co.th/download_center.asp
4/29/2014 7:21:37 AM •
Kyocera...
•
37 views • 0 helpful votes
Error message
The drum unit is not installed properly. open the left door remove the toner wast bottle puch on the gray little plastic to remove the drum unit rienstal the drum unit firmley,instal the wate bottle back close the left door,and hopffuly will work
.
4/9/2014 2:30:05 AM •
Kyocera...
•
51 views • 0 helpful votes
7410:0111301
Most probably the drum unit has shifted slightly out of position. Remove the toner/process unit, open the cover on the left side of the machine, Remove the waste toner bottle. You will see a grey release button for the drum unit, press it in, slide the drum unit out a couple of inches and slide it back in firmly so that it seats and clicks in completely. Reinstall removed parts. Should be good to go.
2/24/2014 3:49:46 PM •
Kyocera...
•
31 views • 0 helpful votes
Not finding what you are looking for?