Top 20 Kyocera FS-4000DN Laser Printer Questions & Answers

no because its a feed source for special paper it wants you to verify what you have loaded

Once you have installed and setup a multi-tray printer you might like to try to print a document to different printer trays. Open a word document and create a two page document.

• Select your new printer under file->Print (if it's not the default)
• Click the page layout tab
• Click the small triangle at the bottom right
• Open the page setup dialog box and click the page Paper Tab
• Choose a tray for the first page and other pages. Close the dialog box and print.

you have a bad engine or main pcb or connection between them

Refer to troubleshooting in the user manual for an explanation of the error and put here if you cannot solve it

Open paper tray, locate the feed roller (small rubbery wheel) and moisten a cloth. Gently clean the roller to remove build up of paper dust from it. Also worth using is some "anti static foam cleanser" on the cloth to help deep clean the rollers, or the pre-moistened "Screen wipes" Also check there is nothing blocking hte paper path, remove paper cassette, and toner catridge (and drum if I recall correctly) and see if you can feed a sheet of paper MANUALLY from tray up into the "imaging chamber" where the toner lives. If this feels too stiff, there could be an obstruction in the way, fragment of paper scrunched up after a REAL jam, or fault sensor arm. If you find something and can remove it, reassemble, and test

Check where the waste toner bottle is, and if it's like the FS2000, the drum unit can be pushed back in from where the bottle attaches to it. Error should then go when you close the lid back down

first try the default pass word of user name:Admin pass:Admin or Admin00

The error is for the drum unit, it may just need reseating or changing. The best thing is to take it out, give it a clean and reseat it. Hope this works for you.

press drum unit open left door and push drum inside.

This error code indicates a problem related to paper cassette lift mechanism. First thing that you will need to check is, if the printer makes some strange noises at initialization, when the printer is trying to lift the paper inside cassette. You can verify if the lift mechanism on the printer is ok, by removing paper cassette and press the 3 small white switches on the left of printer. At this moment the printer is trying to lift the cassette and you will see a gear that rotates on the right side of printer. Also verify if the GEAR LIFT Z64 is intact by opening the gearbox(the big one from the gears from the right side of paper cassette). This gear is cracked in most cases. Replace it.

Call service 2000 main motor error

There is a limit switch that detects when the paper is up.Check it to see if it moves freely.

C0150 Engine PWB EEPROM Backup Memory Device Problem. EEPROM cannot be written or read. C0150 This is what Kyocera says the problem is.

make sure dial on front of cassette matches paper size in cassette

pull the toner and developer (they come out as one unit unless you delibrately seperate them) out of the top of the printer. Open the side door on the print and remove the waste toner bottle. You'll see a gray button above where the bottle was. Push the button and pull the drum out about a half and inch. Push back in firmly until it clicks. Reinstall bottle and reinstall toner and developer. Should work from there, but you may have to power off, then power on.

Toner motor lock error ,usuall ycaused by using non manufacturer toner ,you may need to get a new developer unit

Toner motor lock error**The top cover interlock switch is damaged and the top cover actuator side does not always seat properly. Replace switch (part of switch regulator pcb) and repair retaining clip

This code indicates that the drum unit is not correctly loaded into the printer. Open the door on the side (where the waste toner container fits) and ensure that you gently push the drum unit into the machine. Your handbook will show you the drum unit.

This error 7410 is a Drum unit non- installing error. The drum unit is not installed or not installed properly.The drum PWB EEPROM does not communicate normal. Detaching and refitting the drum unit;Procedure Remove the developer unit Procedure 1. Open the top cover.2. Open the MP tray.3. Remove the developer unit.4. Check or replace the developer unit and refit all the removed parts.5. Open the left side cover and then remove the waste toner box.6. Unlock the drum unit lock and then remove the drum unit.7. Check or replace the drum unit and refit all the removed parts.Good Luck