20 Most Recent Whirlpool 3.2 cu. ft. Plus Washer - Page 6 Questions & Answers

This sounds just like a bad coupler. It is what connects the motor to the transmission. If you remove the case you will first see the water pump. Then the motor, the coupler is on the motor shaft on the other side. The coupler consist of three pieces. One on the motor shaft, one on the transmission and the other is in between the two.
If you have never been inside a Whirlpool, you first take a screw out of each end of the console. Then pull froward and flip the console over the back out of your way. Then un clip the clips on each end, unplug wire in the middle of where the console was. Then pull forward on the case. It will rise up in the back and then come off. This is when you will see the water pump. Good luck.
Please rate solution

Sounds like your lid switch is bad and or broken replace it and your back in business

Sounde like a bad lid switch . With no model number , can't help you further .

Hi there.

Windows OS comes wid a MSN pre-installed, however i suggest u to download a new version of it from Here .

In order to start using it, u need to get registered or sign up with MSN or use any of Hotmail or windows live id.

Once ur done with the sign up, u will be able to login thru MSN. And share the ID with ur friend.

Enjoy,

Hope it helps You.

Regards Take Care

the most common problem when this occurs is the lid switch has broken inspect it if not click when lid is closed replace the switch you see if you can get local it saves some shipping cost unless they are outragious then order on line

Lid switch has gone bad. You can bipass, but better to replace switch, they should only cost about $10. It is there for safety purposes. I’m happy to help further over the phone at https://www.6ya.com/expert/josh_87ce33216d7b2148

Change the motor drive/start capacitor

If the washer will fill and drain, but won't agitate or spin, you may have a broken motor coupling. The noise of the motor engaging, lack of agitation and ability to still drain are the usual symptoms. This is a common fail item with this model washer through normal wear and tear. Newer versions of the coupler are more resilient and resist breaking. The following link explains how to replace one:

http://www.fixya.com/support/r385250-replacing_motor_coupling_kenmore_top

The motor coupling is located between the drive motor and the transmission and takes the place of a drive belt. They do wear out and can break. The replacement part number is included in the link I provided and is an improved upgraded coupling that is more resilient. It should last longer. If you have questions, or require additional assistance, please let me know. I hope this helps you.

A replacement coupler can be purchased on line at appliancepartspros.com for about $11. Just use the part number in the link and "Search by Part Number" for your search criteria.

Now...a washer that fills and doesn't do anything, or stops right after the wash cycle and then does not advance to the rinse cycle and drain is commonly caused by a lid switch malfunction. The lid switch is usually mounted under the washer top casing, on the right hand side on most top load models. It is activated by a plastic piece on the lid (called a "Lid Strike") through a small hole on the rim of the wash tub opening. In many cases the lid strike breaks off the lid, or the lid switch becomes loose and no longer makes contact. Inspect the lid to make sure the lid strike is still intact, and then inspect the mounting screws (adjacent to the small opening on the wash tub rim) and make sure they are snug.

If the switch is not activated by a lid strike, it will activated by a hinge actuator located next to either the left or right lid hinge. You will need to remove the operator console in order to access this type of switch.

If you determine the switch to be defective, the following link explains how to replace one:

http://www.fixya.com/support/r385198-replacing_lid_switch

If the switch requires replacement, a new one can be purchased on line at searspartsdirect.com, pcappliancerepair.com, repairclinic.com, appliancepartspros.com. Just use your model number as your search criteria. All these sites offer competitive pricing, so shop all them for the best price.

Take note of your symptoms:

1. Washer fills, may or may not agitate, will not advance to the rinse cycle, and will NOT drain - lid switch.

2. Washer fills, does NOT agitate or spin, but WILL drain - motor coupling.

If you still have questions, please let me know. If the suggestions I have listed do not match your washer symptoms, please post back and elaborate more on what the washer is/is not doing. That way I can provide you with better assistance. I hope this information is helpful to you.

If your are having a cold water supply problem, check the solenoid at the water inlet valve. I will attach a photo for reference. Use a multimeter or ohmmeter to test the solenoids for continuity. A lack of continuity indicates a faulty solenoid and the water inlet valve will have to be replaced. Hope this helped and best wishes.

http://www.youtube.com/watch?v=WLPGs2UMUJc

This video will show how to replace the direct drive coupling that runs the transmission.

More than likely motor has lost a stage in it. I would replace it.

belt is off

Pop the lid open from the front or sides of the top panel. This should expose the switch. Pretty simple task. Just remember what you do. Don't forget to disconnect power cord before servicing.

if it is a newer machine whirlpool does not use belts they use couplers, if you need tech assistance live go to www.whirlpoolpartssurplus.com

I had the same problem, you need to turn the washing machine on it's side and look for a pin hole leak in the seam of the plastic holding drum on the bottom. I used a silicone sealant, "GOOP" , let it dry for 1 day and problem solved. It has not leaked in two years. good luck!

direct drive coupling.

This is likely a lid switch problem. They tend to get weak and work sometimes and sometimes not. When it stalls like that try pushing down on lid and see if it kicks in. If so you need to replace the lid switch

Replace water pump. Common problem. Unscrew the control panel ,two screws on each end. Flip control panel over and unsnap gold brackets from base to the back. Lift up housing and disconnect lid switch, remove housing. The water pump is in the front lower that has two hoses , disconnect hoses and unsnap pump. My sister fixed hers in about 25 minutes.

your out let hose is split,,cheers