20 Most Recent Dynex DX-LCD37 TV - Page 4 Questions & Answers


POWER BOARD = $54.99 "http://cgi.ebay.com/Dynex-DX-LCD37-09-Sub-Power-Supply-Board-BA71F0F01026-1-/160540235334?pt=LH_DefaultDomain_0&hash=item2560f19646"

INVERTER =
$89.95 http://www.discount-merchant.com/ProductDetails.asp?ProductCode=1183673&Click=54985"

THE SCREEN

http://cgi.ebay.com/Dynex-DX-LCD37-09-Screen-only-/330543674141?pt=LH_DefaultDomain_0&hash=item4cf5f0331d
which cost
US $169.00 Buy It Now(will expire in 8 days)



Dynex DX-LCD37... | Answered on Apr 09, 2011


Hi,

I think you will find that all of your channels are still there. If you are using digital or digital and analog channels, some of the digital channels may be on "sub-channels". This is explained on page 14 of your Dynex user manual. For some channels you will need to enter the main channel number - e.g. 8 - followed by a decimal point, then the sub-channel number - e.g. 8.3

The decimal point is below the 7 key. The easiest way to check whether you have sub-channels or not is to press the GUIDE key in the top-right corner of the remote for a complete list of the digital channels.

It's difficult to determine what is causing the 'fuzzy' picture. I would advise you to disconnect the coax connection at the back of the TV, inspect it for any damage, then re-connect it. It could also be caused by interference from another electrical device. Some TVs have better interference suppression than others and it's possible that your old Toshiba was better at eliminating interference.

There is also the possibility that you bought a lemon. I suggest you concentrate on making sure you have all the channels first then we can look at possible reasons and cures for the fuzzy picture. You don't want to spend too much time (or money!) getting it right if you can't get all the channels and you end up returning it to the shop.

Please check for the digital sub-channels first then reply to me by clicking on "Add a Comment" below your question.

Regards,
BElectric

Dynex DX-LCD37... | Answered on Apr 02, 2011


If you are referring to a cable signal on your tv set, then there are several ways, but first off, how do you know the signal is weak? Analog cable signals typically run at 30 to 40 percent while HD signals on the same line can be as high as 90%.
If your cable connections are firm and have no fray with good cable runs, and is not longer than needed, I would suggest calling the cable company tech support line for troubleshooting. It could be their error in an outside line.

Dynex DX-LCD37... | Answered on Mar 23, 2011


It will need in-depth troubleshooting, power supply will be the first place to check.
If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on:

Basic LCD monitor and TV troubleshooting guide:
http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide
http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting
http://www.fixya.com/support/r7406380-tv_training_manuals
Failed TV and Monitors: http://s807.photobucket.com/albums/yy352/budm
Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague
Parts: www.shopjimmy.com
Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx he can make you a set of caps.
Or www.digikey.com, just make sure to use caps with low ESR, 105c, high ripple current and long life rating such as PANASONIC FM or FC series.
Please post back what you find.
Please leave rating if it helps.

Dynex DX-LCD37... | Answered on Mar 03, 2011


Do you have a cable or satellite box connected to the TV? If so the box is probably what is providing the Closed Caption and not the TV.

Robert

Dynex DX-LCD37... | Answered on Feb 26, 2011


click the zoom button on remote control.

Dynex DX-LCD37... | Answered on Jan 23, 2011


1. Find the volume control icon on the bottom right portion of your screen 2. Right click the icon 3. Select change default 4. Cycle through the options until you see the logitech speakers as an option 5. Select this new option 6. If you still do not see the logitech speakers then you need to reinstall them with the provided software. If you do not have software, download it for free from logitech.com

Dynex DX-LCD37... | Answered on Jan 21, 2011


For this TV, the TV speaker on/off is independent of the headphone jack. Make sure the plug for the headset fully seated in the jack (mono versus stereo fit differently).

The manual is available at the bottom of the list here: http://www.dynexproducts.com/productSearch.html?query=DX-LCD37&mode=manuals .

I hope this helps.

Cindy Wells

Dynex DX-LCD37... | Answered on Jan 20, 2011


I HAVE THE SAME PROBLEM, HOW CAN WE FIX THIS???

Dynex DX-LCD37... | Answered on Jan 17, 2011


On the dvd player and on your tv, you should have 3 jacks. Yellow, for video, Red for sound, and white for sound. Just match the colors. Then on your tv, change the channel to AV or Input

Dynex DX-LCD37... | Answered on Jan 06, 2011


vido settings what?

Dynex DX-LCD37... | Answered on Dec 27, 2010


Use Insignia codes.

Dynex DX-LCD37... | Answered on Dec 27, 2010


Have you tried doing a factory default reset from the menu?

Dynex DX-LCD37... | Answered on Dec 22, 2010


Easy, You plug either the HDMI cable into one of the HDMI inputs and then plug it into the XBOX 360. If you are using either the component or composite cables then plug them into the proper color coded input.

Dynex DX-LCD37... | Answered on Dec 22, 2010


I had a similar problem with my 42 in Philips LCD HDTV.


Here was the problem. My Power Supply Board had several bad capacitors. I opened my TV (warranty was expired of course) and found four bulged capacitors on the PSB. Many major electronics companies Philips/Magnavox, Sony, Panasonic, and others were sold capacitors that failed in 2-5 years instead of 10-20. The capacitors fail prematurely due to a lack of preservatives. Unfortunately, they were installed in all sorts of devices and cause a wide range of failure problems.


Here are some options for you.


1. Have it fixed by a professional $$$$$$$??????? (Is it under warranty?)

Remember, TVs CONTAIN HIGH VOLTAGE AND CAN KILL YOU! Do this at your own risk.

2. Open your TV and find PSB. (The board that the power cord plugs into) Check for faulty caps. If you find some (bulged or leaking) bad caps replace the entire board. The entire board costs around $250 right now because they are in high demand right now. They can be found online. I would definitely shop around though.


3. Remove and then replace individual faulty caps. This takes some soldering skill.

Caps are inexpensive and if you can take care of it yourself it will save you hundreds.


This may be your problem. If you determine that it might be.

I have a Tip/How TO tutorial on this site that may also help. It gives step by step instructions for replacing caps on PSB #715t2432-2. If this is your board you are in luck. Here is the Link: Fixing the Philips Turns/shuts off on its own problem. I'm working on uploading pictures to help guide people though the process as well. Let me know if I can do anything to help.


Hope this helps and if it does please rate it accordingly. Good luck.

Dynex DX-LCD37... | Answered on Dec 19, 2010

Not finding what you are looking for?
Dynex DX-LCD37 TV Logo

213 questions posted

Ask a Question

Usually answered in minutes!

Top Dynex Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76177 Answers

Cindy Wells

Level 3 Expert

6048 Answers

Vitally Alcher

Level 3 Expert

1645 Answers

Are you a Dynex Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Dynex Televison & Video

  • Dynex Televison & Video

Most Popular Question

power surge caused dynex 37 lcd

  • Televison & Video
Loading...