20 Most Recent
Dynex DX-LCD37 TV - Page 5 Questions & Answers
Connected the cables to the
okay lets do a cable check... cable from wall /outside connected to cable box in, from the cable box out to (please note any DVD recorder or VCR should be connected here if you have and then on to TV) TV in ..... TV on , turn to channel 3 (this should be the only ch locked on the TV no scan is needed) you are using coaxial cables... if this was/is a hi def connection (your set should be on component)
My TVs power supply transformer seems to have
HI,
your tvs samps transformer may has no problem. the fuse blows because there is some other components which drives the smps transformer may be faulty. check the smps driving mofets of that three transformers before buying a new transformer. also check the MOV placed after fuse. if it is shorted the fuse will blows.
ok
Blinking light on 37" Dynex LCD
I had a similar problem with my Phillips 42 in. LCD HD TV.
Here's the problem. The Power Supply Board. I opened my TV
up(warranty was up of course) and found several bad capacitors.
Phillips and several other companies were sold capacitors that although
were highly rated failed within 5 years because of a lack of
preservatives. All sorts of electronic equipment is now being effected
due to these defective capacitors.
Solutions?
1. Take it in and have it fixed
2. Open it up, check the board for faulty capacitors(bulged or leaking) Buy a new Power supply board and install it.
3. Remove PSB, remove faulty capacitors and replace with compatible new ones.
Hope this helps
When the power is turned
Had a very similar problem with mine - not sure if this will help or not, but it seems to be doing the trick (channels scanning as I type).
I unplugged the tv for about an hour. I unplugged the cable, and all the components. Then I turned the tv on, and was able to get to the menu screen. Previously, I couldn't change channels or even power off from the buttons on the side of the unit either...
Once there, I plugged the coaxial cable directly into the side of the set, then ran the auto-scan.
I know it's not a techincal answer, and a bit strange, but as I mentioned, it seems to be working for my issue.
Good luck!
Volume on the tv
You must first determine if the audio in the television set is still working. You will need to connect the television audio output to a stereo input. Then try using the volume control and see if the circuit responds normally. If the circuit responds normally , you have a problem with the television speakers. They can can be serviced or replaced. If the circuit does not respond normally you have a much more serious problem in the audio circuits.This is usually found on the main controller board. The probelm could be with cold solder joins, component failure, or a bad audio processor ic. These problems will have to be serviced by a service center. They will have all the correct service information to test the television and repair it. You can call Dynex customer support at this telephone number 1-800-305-2204 between the hours of 7am-12am CST. Give them the model number of your television and tell them about the problem with a loss of audio. They will be able to tell you how you can get the television tested and repaired. I hope this information helps you with your problem.
How can I configure the picture to match screen
There is a # button (hd zoom) on your Comcast remote that will adjust the picture size. Also make sure you are set to the proper resolution on the Comcast receiver (720p) and that the Dynex television is set to the proper input for high definition.
Philips 26PF5521d LCD TV turns on screen lights
Tries unplug,replug the tv back like an hour later.Now,the tv is resetting itself back to the factory setting.The tv now,should work again.Not,than the power supply board is the cause.That the board,where the power a/c cord plug into it.Tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.
I have a DYNEX LCD37 for 2 years, it was working
The tv Tuner signal board have problems,might need the replacement of the Tuner signal board it self.Tries the tv unplug,replug it back in like an hour later.Let the tv resetting itself back to the factory setting.See,if that solved ur problems.Not,than the Tuner signal board have problems itself,must be replaced the Tuner signal board itself.
Do i need to use HDMI wire if i have a cable box ?
It depens on what the cable box outputs are, you need to see if it has RF Coaxial jack (use CH3 or CH 4 on the TV), composite video out (Yellow RCA jack) with red and white RCA for audio, component video outputs (Red, Green, and Blue RCA jacks), or HDMI output jacks. HDMI and component video are for HI-DEF if you subscribe to the HI-def package. The cable company should provide you with the owner manual. Please post back with more info.
Failed TV and Monitors: http://s807.photobucket.com/home/budm/allalbums
How to mount on wall
first you neeed to buy a wall mount kit for your size tv, menards or lowes is cheaper than best buy. you can also purchase a box for behind the tv that has a cable and power supply, it mounts in the wall so you see any wires. you must take the tv base off, normally 4 screws and make sure you have studs where you would like to mount the tv
Wii remote hit screen. can it be fixed
if it looks like a spider web on the screen, yes but the repair cost will be more than buying a new tv.. sorry any damage to the screen on a plasma or lcd normally costs more than the tv. you can however try to sell it for parts, such as power supply etc and also the remote
Not finding what you are looking for?