Frigidaire GLEH1642DS Front Load Stacked Washer/Dryer - Answered Questions & Fixed issues

here ya go as far as getting the part. https://www.repairclinic.com/Shop-For-Parts/-x676c6568313634326673/Gleh1642fs-Parts they too have a very helpful chat or 800 team to answer questions many times when you select the part there is a install section. Hope this helps. I know as I had this problem. If you need directions I can help but tis a bit detailed. maybe a youtube video on it helps to look when you know what part # your installing and what it's called Have a good evening..

I have a GLEH16242 Frigidaire/Electrolux stacking washer/dryer. The main bearing went out on the washer. I did the expensive fix of replacing the outer drum/bearing assembly in hope of nothing going wrong. Everything went together well, but now it won't go into high speed spin. It does if I have no clothes in it, but as soon as I introduce clothes it only does the 'medium spin' but never advances to the high. I've changed shocks, confirmed the door switch is working properly and double checked level. Even placed it on a big thick sheet of plywood in hops of stabilizing it more. It does have a wobble to it when it starts spinning, but when it kicks into medium spin, is smooths out.

Hello friend, thank you for your inquiry! I understand that your Frigidaire washer is not spinning I would suggest checking the drain hose to assure it is not restricted or too long. If the hose checks out you could have an issue within your belt, pulley, motor, or control. Since it could be any one of these underlying issues I would recommend having a professional come out to properly diagnose and repair your appliance. -Matt

Hey Salvador Juarez, I appreciate your post!

I understand that when you try and press the dryness cycle on your Frigidaire laundry center it provides you an error. I would like to ask you some additional questions in order to best assist you. Does it show you a code or beep? If so, how many times does it beep? I look forward to your response. Thank you. -Matt

Good Morning Joel, I understand the dryer on your laundry center, model# GLEH1642DS, will not power up, but the door light comes on. Please try resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. Restore power and try any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful. -Best Regards- WP

Good Afternoon Friend, I understand you want to know how to fix the locking mechanism on your Frigidaire laundry center, model# GLEH1642DS. Typically, this is not a do it yourself repair, as there are no step by step instruction manuals. I suggest contacting your local authorized technician for further assistance. They have been trained on your particular appliance, and should be able to fix the locking mechanism with ease. Hope this is helpful. -Best Regards- WP

Good Afternoon Friend, I understand that the washer timer on your Frigidaire laundry center, model# GLEH1642DS, stopped turning and you want to know how you can diagnose this. Typically, this is not be a do it yourself repair, as there are no step by step repair instructions. I suggest contacting your local authorized technician for further assistance. They have been trained on your appliance and should be able to diagnose it and determine what is causing the timer button to not turn. Hope this is helpful. -Best Regards- WP

Good Afternoon Friend, I understand that you want to turn the buzzer off of your Frigidaire dryer, model# LGR331SO. With your model dryer, you are not able to turn the buzzer off. I hope this is helpful. -Best Regards- WP

Hello Reese, I see that you're having a Problem with your Frigidaire GLEH1642DS Front Load Stacked Washer/Dryer. I see that the washer will not work until dryer is turned on and the dryer will not heat. I would recommend giving the appliance a hard reset. You will do this by either unplugging it or switching the circuit breaker off that the appliance is attached to. When you do this you will want to leave it off for 3-5 minutes. Once the 3-5 minutes has elapsed, bring power back on and try to restart it. If you are still having trouble with the washer not working until dryer is turned on and the dryer will not heat. I would suggest contacting your local authorized technician to diagnose and see why you keep receiving this error code. -Best Regards-

major problem, could be transmission or timer switch cost for repair could be high

Here you go!

Here is the door for you to order.

see this causes and use the common sense.God bless youIf your dryer doesn't heat, check these: Igniter Gas valve coils Thermal fuse Igniter Modern gas dryers use an electric igniter to ignite the gas from the gas valve. When it's working properly, the igniter glows bright orange. When it burns out, the dryer tumbles but there's no heat because the gas can't ignite. When the igniter burns out, you need to replace it. If the igniter is held by a tension bracket, you very well may need to replace the bracket too. To determine if the igniter is burned out, watch the part testing video at the bottom of this page. The igniter is inside the dryer housing, near the bottom front, usually in a cone-shaped metal tube (the force cone). It's about 2 inches long. It's mounted to the far end of the burner tube, and it has two wires attached to it--or to the tension bracket, if there is one. Gas valve coils Watch the igniter. Does it glow bright orange, then shut off without igniting the gas? (When the gas ignites there's a large blue flame.) If so, there may be defective coils on the gas valve. Mounted on the top of modern gas valves, there are black electrical coils. The coils, when energized, open the gas valve. If one or more of the coils are defective, the valve doesn't open and the gas cannot ignite. Because it's often difficult to properly test the coils, it's usually best to replace both (all) of them at the same time. Thermal fuse On many dryers, there's a thermal fuse (a heat-sensitive fuse that blows if the dryer overheats) mounted to the exhaust duct inside the back cover panel. The fuse is about an inch long. It's usually embedded in black resin and mounted in a white plastic housing. If the fuse has blown, it has no continuity. When this happens, your dryer either just stops heating, or it doesn't work at all. Be sure to inspect the venting/heating system before replacing the fuse to put the dryer back into operation. (You can't re-set this type of fuse.) To determine if the thermal fuse has blown out, watch the part testing video at the bottom of this page.

Please check the link below:http://www.espares.co.uk/advice/washing-machines/a/7/1393/how-to-replace-the-element-in-a-washing-machi.html

The most likely suspect is the heater assembly, Part #131475300 But as you can see in the photo you are going to have to disassemble the drum to get to it (Item 15 in the photo)

You can buy a new knob. Try http://www.appliancepartspros.com. The washer timer knob part number is AP2106210. Hope this helps you.

The buzzers (there are two, one for the washer, one for the dryer) are behind the control panel. 6 screws must be removed to access the back of the control panel: 2 for the service panel, the 2 outer screws at the base of the control panel, then the 2 much smaller-sized screws.

The buzzers, in my model, are small, un-buzzer-like-looking little black boxes stamped with the brand name 'Ark-less'.

The buzzer for the dryer is connected to 2 contacts on the back of the dryer timer, the contacts labeled 'H' and 'C'.

Once you've identified the buzzer for the dryer, you should be able to find the one for the washer. It's connected by one white and one grey wire.

You should be able to verify this info using the wiring diagram, which will be located behind the service panel. If I remember correctly, the buzzers were labeled 'signal' on the diagram.

teri maaa ki gussa kyo ho bhaui pooja karunga

yes always unplug the unit from it's electrical supply before you work on any part of the washer or dryer.....

Final spin does not appear to be working. Clothes are soaking wet after the buzzer has gone off. Any ideas would be helpful. Thanks.