Top 20 Kyocera FS-1016 Printer Questions & Answers

1087 1087 163 print key

I was able to resolve the dreaded 009-654 on my c1765nfw.

• Download/install the usb driver for the printer
• Connect the printer to a usb port on my computer
• Download the latest Dell printer firmware driver
• Re-power the printer on with a toner cartridge removed
• Run the Dell firmware upgrade program, it should recognize that the printer is connected and will load the firmware
• When the firmware installation is completed, restart the printer and everything should be working again.

This solution may work on all other Dell printers that experienced the same error.

Check this pdf https://www.google.gr/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&cad=rja&uact=8&ved=0CCAQFjAA&url=http%3A%2F%2Fwww.diagramasde.com%2Fdiagramas%2Fotros2%2FService%2520Manual%2520FS-1016EN.pdf&ei=57nXU-S_MYj9ygP4yILYBw&usg=AFQjCNEJEfHI-JBO5wAgJrl8GtSiN847Xg&sig2=1AjtVPSzEtEcdpGaZJrjVQ Spefically read page 1-5-8 until 1-5-12

my dear you chek exp lamp

Remove and reinsert the two connectors of the fuser unit. If not, then remove and reinsert all the connectors from the engine pwb and the power pcb.

Check the lamp and the thermostat for continuity. Check the operation of the thermistor. If something defective replace. Most common is the thermostat. In addition, check the operation of the cooler fan on the machine's left. If it is not working then you have to fix or replace it. The most rare but existing failure is call service 6000 due to defective power supply. In this case the heat roller is stuck on press roller.

The service manual is located here: http://servicemode.ru/images/stories/files/kyosera_fs_1010_sm.pdf Under section 6-16 you can find error (5) 6000. It is a fuser unit error.

Buenos dias no se que hacer cada que doy a imprimir me sale error call 6400 llame servicio tecnico, a que se debe y que puedo hacer

Shows as a fuser error (zero cross signal error)but we see this being the power supply and/or bad power to the unit. Check your power outlet (it should be on a separate or dedicated plug with no other devices). Remove and re-seat the drum unit and DV unit. Could be the fuser but if it comes back its the power supply

Shows as a fuser error (zero cross signal error) but we see this being the power supply and/or bad power to the unit. Check your power outlet (it should be on a separate or dedicated plug with no other devices). Remove and re-seat the drum unit and DV unit. Could be the fuser but if it comes back its the power supply

HOW DO I RESET ERROR C6400 FOR OLIVETTU D-COPIA 18MF

error serv.2000

yacine

If you get the Engine Panic error message, you need to turn the power switch off and then back on again. If that doesn't fix the error, contact a service representative to help resolve the problem.

This is french. It says "Printer Error - Call Serv. 9780".

Disassemble and look the fan side of the fuser, there you will see that the wires pass through a **** that is more of a cover remove it and there's the can on that side is where will the current regulator and the high card that connects to the source card,
Well it happened to me this issue, I found the card and it was high toner developing unit that was discarding, in addition to the seal of the doctor blade was worn out, another issue I found was current leakage, what I did was make the can land top with more pressure to the high card, in addition to not fall toner worn by the seal tape to tape the holes in the chassis, after that I have not been flawed

You can download it from here

Broken heater lamp error

The temperature won't rise by 1°C/33.8 °F during warming up and the heater is turned on for 5 seconds.

The temperature won't rise by 1°C/33.8 °F during printing and the heater is turned on for 5 seconds with the duty cycle more than 60%.

1. Defective fuser thermistor.

2. Broken thermal cutout or heater lamp.

3. Defective engine/high voltage PWB.

Turn power switch off, and remove power cord.

Detach YC7 connector on the engine/high voltage PWB.

Measure resistance between pins 1 and 2 of the detached connector.

Open (infinite)?

Yes Then - Replace the fuser thermistor.

No Then - Detach YC1 connector on the power source PWB.

- Measure resistance between pins 1 and 2 of the detached connector.

Open (infinite)?

Yes - Replace the thermal cutout or heater lamp.

No - Replace the engine/high voltage PWB.


I hope this was helpful,
Shawn

it seems that the problem is with your printer toner..so replace the toner. may be the toner is faulty