Kyocera FS-1016 Printer - Answered Questions & Fixed issues


1087 1087 163 print key

Kyocera FS-1016... | Answered on Aug 18, 2019 | 541 views


my dear you chek exp lamp

Kyocera FS-1016... | Answered on Jul 08, 2015 | 395 views


I was able to resolve the dreaded 009-654 on my c1765nfw.
  • Download/install the usb driver for the printer
  • Connect the printer to a usb port on my computer
  • Download the latest Dell printer firmware driver
  • Re-power the printer on with a toner cartridge removed
  • Run the Dell firmware upgrade program, it should recognize that the printer is connected and will load the firmware
  • When the firmware installation is completed, restart the printer and everything should be working again.
This solution may work on all other Dell printers that experienced the same error.

Kyocera FS-1016... | Answered on Dec 04, 2017 | 1,564 views


Have you tried just setting it up as an HP? Kyocera machines emulate HP.

Kyocera FS-1016... | Answered on Jun 12, 2014 | 474 views


Remove and reinsert the two connectors of the fuser unit. If not, then remove and reinsert all the connectors from the engine pwb and the power pcb.

Kyocera FS-1016... | Answered on Jun 11, 2014 | 324 views


Check the lamp and the thermostat for continuity. Check the operation of the thermistor. If something defective replace. Most common is the thermostat. In addition, check the operation of the cooler fan on the machine's left. If it is not working then you have to fix or replace it. The most rare but existing failure is call service 6000 due to defective power supply. In this case the heat roller is stuck on press roller.

Kyocera FS-1016... | Answered on Jun 11, 2014 | 118 views


Buenos dias no se que hacer cada que doy a imprimir me sale error call 6400 llame servicio tecnico, a que se debe y que puedo hacer

Kyocera FS-1016... | Answered on Jan 21, 2014 | 323 views


The service manual is located here: http://servicemode.ru/images/stories/files/kyosera_fs_1010_sm.pdf
Under section 6-16 you can find error (5) 6000.
It is a fuser unit error.

Kyocera FS-1016... | Answered on Jan 12, 2014 | 245 views


Shows as a fuser error (zero cross signal error)but we see this being the power supply and/or bad power to the unit. Check your power outlet (it should be on a separate or dedicated plug with no other devices). Remove and re-seat the drum unit and DV unit. Could be the fuser but if it comes back its the power supply

Kyocera FS-1016... | Answered on Dec 26, 2013 | 228 views


Shows as a fuser error (zero cross signal error) but we see this being the power supply and/or bad power to the unit. Check your power outlet (it should be on a separate or dedicated plug with no other devices). Remove and re-seat the drum unit and DV unit. Could be the fuser but if it comes back its the power supply

Kyocera FS-1016... | Answered on Dec 26, 2013 | 125 views


HOW DO I RESET ERROR C6400 FOR OLIVETTU D-COPIA 18MF

Kyocera FS-1016... | Answered on Sep 03, 2013 | 226 views


This is french. It says "Printer Error - Call Serv. 9780".

Kyocera FS-1016... | Answered on May 24, 2013 | 360 views


error serv.2000

Kyocera FS-1016... | Answered on Nov 26, 2012 | 121 views


If you get the Engine Panic error message, you need to turn the power switch off and then back on again. If that doesn't fix the error, contact a service representative to help resolve the problem.

Kyocera FS-1016... | Answered on May 08, 2012 | 1,531 views


it seems that the problem is with your printer toner..so replace the toner. may be the toner is faulty

Kyocera FS-1016... | Answered on May 08, 2012 | 240 views


Disassemble and look the fan side of the fuser, there you will see that the wires pass through a **** that is more of a cover remove it and there's the can on that side is where will the current regulator and the high card that connects to the source card,
Well it happened to me this issue, I found the card and it was high toner developing unit that was discarding, in addition to the seal of the doctor blade was worn out, another issue I found was current leakage, what I did was make the can land top with more pressure to the high card, in addition to not fall toner worn by the seal tape to tape the holes in the chassis, after that I have not been flawed

Kyocera FS-1016... | Answered on Jul 14, 2011 | 834 views


You can download it from here

Kyocera FS-1016... | Answered on Jun 08, 2011 | 1,262 views




Broken heater lamp error

The temperature won't rise by 1°C/33.8 °F during warming up and the heater is turned on for 5 seconds.

The temperature won't rise by 1°C/33.8 °F during printing and the heater is turned on for 5 seconds with the duty cycle more than 60%.


1. Defective fuser thermistor.

2. Broken thermal cutout or heater lamp.

3. Defective engine/high voltage PWB.


Turn power switch off, and remove power cord.


Detach YC7 connector on the engine/high voltage PWB.


Measure resistance between pins 1 and 2 of the detached connector.


Open (infinite)?

Yes Then - Replace the fuser thermistor.

No Then - Detach YC1 connector on the power source PWB.

- Measure resistance between pins 1 and 2 of the detached connector.

Open (infinite)?


Yes - Replace the thermal cutout or heater lamp.


No - Replace the engine/high voltage PWB.


I hope this was helpful,
Shawn

Kyocera FS-1016... | Answered on Dec 28, 2014 | 4,344 views

Not finding what you are looking for?
Kyocera FS-1016 Printer Logo

97 questions posted

Ask a Question

Usually answered in minutes!

Top Kyocera Office Equipment & Supplies Experts

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Are you a Kyocera Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...