20 Most Recent Maytag Gemini 30" Self-Cleaning Freestanding Electric Double Oven Range - Stainless-Steel - Page 4 Questions & Answers

many burners have safety mechanism that shuts the flow of gas when it is cold. it is there to prevent the flow of gas in the case when the fire was put out by wind or split of water.
you didn't mention if after the fire is lighted, are you able to turn the knob back to low.

I have the same problem. Happened a few days ago. Have you found a solution?

Hi,

Here is a tip that I wrote that will help figure out why the burner spark keeps on clicking...Gas Range Repair Burners Keep on Clicking

heatman101

F8 Analog / Digital problem Replace clock (ERC).

Hi,
Before you go working too hard to get you oven to go into the self clean mode(self destruct)....check out this tip...

Self Cleaning Oven Problem
http://www.fixya.com/support/r3969401-self_cleaning_oven_problem

heatman101

" Wish I had read this first. I never would have used the self cleaning option. Thanks for the info!!

"F1:2" is a Runaway Cook Lower Oven error. This indicates that the oven temperature sensor is defective and needs replaced. The following link explains how to replace an oven sensor on most ranges:

http://www.fixya.com/support/r393313-checking_replacing_oven_probe


Replacement parts (if required) can be purchased at any of the following websites:

pcappliancerepair.com
appliancepartspros.com
searspartsdirect.com
repairclinic.com

Prices vary between these sites, so shop and compare. The first three sites listed also offer helpful exploded view diagrams to help you locate and properly identify the parts you need.

If you have any questions please post back with your MODEL NUMBER and let me know. I hope you find this information helpful.

most likely the element needs replacing, check for arcing holes,melted spots. check fuses, normaly under cover at top of stove. element is easy to replace(a few screws), unplug stove when doing so.

We have seen this error due to failed components on the control board. If the thermistor and connection look ok, it is probably your control board. They can be bought new or rebuilt at www.fixyourboard.com

Hi,
Before you go working too hard to get you oven to go into the self clean mode....check out this tip...


http://www.fixya.com/support/r3969401-self_cleaning_oven_problem

heatman101

" Wish I had read this first. I never would have used the self cleaning option. Thanks for the info!! "

Hi,
Before you go working too hard to get you oven to go into the self clean mode(self destruct)....check out this tip...

Self Cleaning Oven Problem
http://www.fixya.com/support/r3969401-self_cleaning_oven_problem

heatman101

" Wish I had read this first. I never would have used the self cleaning option. Thanks for the info!!

wwwwwwww
wwwwwwwwww

Hi- There are a few on either side of the control panel assembly, under the covers. They like to hide them. Some models have connectors for the wiring harness to top, so you can remove whole assy. to work on it. Helps to have somebody hold top while plugging/unplugging though. Pay close attention to which wires go where when replacing element.  Let me know if this info helps- have more if ya get stuck! Thanks- Ed

My answer is to NOT use that feature, as generally after most people use that :Feature" straight after the oven faults, you see that "Cleaning" mode simply heats the oven up wayyy up to like 900 degrees up, and after this the temperature sensors generally "Go" so my advice is ... use elbow grease and save a lot of possible problems, especially with a 8 - 10 yo unit.

We provide free diagnostic information when you tell us what brand and model number you are having issues with.
We are available from 7 AM – 7 PM CST. We also provide part removal/installation instructions for our customers when parts are purchased through us.
It is our goal to get you back up and running again ASAP, so please contact us when you need us to help you.
We look forward to hearing you and hope that you have a terrific day. Thank you, Ella
http://www.fixya.com/repair/d499389-accurate_appliance_repair_service

Yes, a control panel is simple to replace if you have instructions.
We are available from 7 AM – 7 PM CST.
We provide part removal/installation instructions for our customers when parts are purchased through us.
It is our goal to get you back up and running again ASAP, so please contact us when you need us to help you.
We look forward to hearing you and hope that you have a terrific day. Thank you, Ella
http://www.fixya.com/repair/d499389-accurate_appliance_repair_service

Sometimes the numbers are either stampped or on a metal plate on the bottom (hinge) part of the door. You could try using the model number and/or serial number of the entire oven.

It means lower oven latch problem, check for obstuctions or replace door latch.

Maytag stove repair in orange county, ca
appliance repair orange county, ca

I am attaching a Gemini manual. The checking procedures are the same for your oven.
Two component suspects for your problem would be the door latch mechanisms and the oven temperature sensors.

http://www.servicematters.com/maytag_library/docs/16010161.pdf