Maytag EPICz 3.7 cu. ft. Washer - Answered Questions & Fixed issues
Machine is flashing f-28
Is this a top or front load? If it is a top load, there should be a tech book for the unit either behind the control panel, or inside a clear plastic bag, located somewhere on the inside of the cabinet ( tilt machine back and look up from underneath. You should look toward the top, front of the unit). The tech book should list all the error codes and tell you what and where to start checking. If it is a front load machine, you can remove the very top, and you should see a tech book on top of the dispenser assembly, or on the underside of the top in a clear plastic bag. Sometimes the tech book is on the back side of the front, bottom access panel ( located under the door). Again, the tech book will have all error codes and what and where to check. Good Luck!
F20 error code on maytag epic any idea what this means?
F20 means that the unit isn't detecting water is entering the machine quick enough. When the error code appears if there is little to no water in the tub, then you have an issue with either the water supply to the washing machine or the electronic water valve. If the washing machine fills up about 1/2 way up the door and is overfilling with the water, it means that your pressure switch is faulty and will need to be replaced because it's not detecting that water is entering the machine.
Maytag fault codes f-28
Locate your Maytag dealer they have the proper tools of the job don't try to do it your self.
The washer showed a code 5d what does this mean
Hi,
5D actually means suds, make sure you aren't using normal detergant as
these units require 'HE or High Efficiency' detergant that doesn't suds
much. Try runing a load with not clothes and just put in a cup of
white vinegar to remove all the suds in the machine and see if goes
through spin with no suds in. If not and you still get an error you
will need to replace the pressure switch because it thinks there is
water or suds in the machine it's not removing.
Let me know,if needed further assistance.
Hope i helped you.
Thanks for using ' Fixya ' and have a nice day!!
How do I remove the
Hi, the first thing you can do is remove the lower bottom front panel. It is held in by 3 screws at the very bottom. 1/2 way accross behind this panel is a hand twistable drain catch. Remove the cap from the drain catch and WATCH OUT water will come out. Remove whatever is in the catch and reinstall it--- you should be good.
Water has leaked from the bottom of the Washer and
F30 - DISPENSER SYSTEM ERROR
When the dispenser motor
cannot be driven to its proper position.
Possible
Causes/Procedure
1.Unplug washer or disconnect power.
2.Check
mechanical linkage from dispenser motor to the top of the
dispenser.
3.Check
wire harness connections to the dispenser motor and Central
Control
Unit (CCU).
4.Check dispenser motor for powered rotations.
Seal is ripped
Yes, the door seal (bellow) can be purchased and replaced. The following link explains step-by-step how to change the door bellow on a Maytag Epic front loader:
http://www.fixya.com/support/r3574186-installing_a_door_bellow_on_a_front_load
Replacement parts can be purchased at any of the following web sites:
searspartsdirect.com
pcappliancerepair.com
appliancepartspros.com
repairclinic.com
I have found these sites to be reputable and provide great service. Prices differ between them, so shop and compare. The firsat three sites I've listed have helpful exploded view parts illustrations to assist you with locating and properly identifying the parts you may need.
If you have any questions about this repair, please post back and let me know. If the link does not take you directly to the instructions I provided, copy and paste the link to your web browser. I hope you find this information helpful.
NOTE: Maytag Epic is manufactured by Whirlpool, so these instructions will apply.
I have a maytag epic z and it suddenly stopped
F21 is a Long Drain error code. This indicates that you have an obstruction somewhere in the drainage system. In most cases, this means you probably have a clog in the drain pump. You may have something getting caught in the pump impeller and slowing it down. Or, you may have something clogging the drain lines. You may also have to remove the inlet hose that runs from the bottom of the wash tub to the inlet side of the drain pump. Debris can commonly clog in this area as well causing the drain cycle to fail.
If this solution doesnt solve your problem, you may have to replace the drain pump.The error code will continue to appear until the pump is replaced.
Codes F-21 And F-33 are showing up
this error occurs if the touch-pad/led assembly is not able to transmit/receive data to/from the central control unit (CCU) 1 check the touch -pad/led assembly by selecting different cycles and changing the modifiers and options available to confrim the touch-pad/led is responding. 2 unplug washer or disconnect power. 3 check wire harness connections to the touch-pad/led assembly and central control unit (CCU) now to the f-33 code system leak if after 30 seconds the control does not detect water entering machine, the valves will be turned off and the error code will be displayed. OR if the control has turned the water valves on and after 8 minutes the flow sensor has detected 10.5 gallons of water passing through it, but has not detected the pressure switch trip, the valves will be turned off and the error code will flash. press PAUSE/CANCEL twice to clear the display. possible causes/procedure 1 check for crack or holes in the washer tub and pressure switch hose. 2 replace components if necessary good luck
ERROR
The error is actually "SD", or more commonly known as "SUD". This is commonly caused by either using too much detergent, using the wrong type of detergent (using regular detergent instead of HE), or a something clogging the drain pump. However, there can be other factors. The following link explains:
http://www.fixya.com/support/r3608687-sud_error
Please read through the link provided and let me know if you have continued problems. I hope this can help you resolve your problem.
Maytag EpicZ Washing machine; basket drive pulley noise & wobbly
sounds like a bad bearing...here is how I check them open the door .lift up on the tub if any play in the upwared monment it's bad...you can also remove belt and pulley spin the tub if you still hear the noise it's bad....
if bad you will have to replace rear outer tub and spinner (it has the shaft on it)
also Give Maytag a call at customer relatiions...make a lot of noise they may just give you the repair..
Not finding what you are looking for?