20 Most Recent Maytag Bravos 3.8 Cu. Ft. Washer - Page 4 Questions & Answers

"ld" is a service code meaning long drainage time
the most likely problem is some lint build up in pump or in the sump restricting water flow into the drain pump

From my manual, it means:

Washer is taking too long to fill.
Check the following:
Are the hot and cold faucets turned on?
Are the water inlet hoses kinked or clogged?
Are the water inlet valve screens clear?
Press POWER/CANCEL to clear display

Hello, Thank You for using FixYa. I will be helping you today.There is no way to change the water level. It washes by spraying the water over the cloths as it moves around.
Thank You and please rate my answer if it was helpful..

hello, you need to install part #W10183157. it comes with instructions itnot that hard to install. it should correct your issue. thanks and please rate me :)

Hello, Welcome to FixYa.
I'm pretty sure I know what you're referring to and in fact I can explain what needs to be done to gain access and repair though it is pretty involved (via removing the tub...it's pretty easy once you see how).

It is most likely the seal under the inner basket (spin basket) and it is a non-serviceable part outside of replacing the complete outer tub assembly as shown here...i.e. If this is a repair you think you can mange let me know, I'll watch for your reply. You may however opt to call a pro. Thank's for visiting FixYa today. Good luck.

Regards,

Macmarkus :)

Unbalanced load. Common problem when washing fitted sheets. The Appliance Assistant wrote an outstanding article about the problems associated with these machines and the solution! HERE If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

check to see if your outflow pump is leaking....mine is....

Hi; F1 flashes when the control detects an out of range pressure signal. Check the following:


A. Check the pressure hose connection from tub to machine/motor control. Is That hose pinched or kinked?

B. If F then 1 repeats numerous times after the Power Button is pressed and the pressure hose connection is not pinched or kinked, replace the machine/motor control.

You can find the proper procedures for replacing the Machine/motor control assembly in this manual I have posted a link to below.

Maytag Bravos Service Manual

Please be advised to the extended download times with this manual. it is very large and contains much information on how to repair this particular unit. The download times may exceed the ten minute mark.

Hi,

Problems with a washing machine not spinning or not draining are often inter related..

If you are having a problem with your top load washer then check out this tip...

Washing Machine does not Pump or Spin


If you are having problems with your front load washing machine then checkout this tip...

Front Load Washing machine not draining and or not spinning


heatman101

What does the Sd code mean?

This code indicates that excessive detergent suds occurred during the cycle. The washer will not be able to spin out water with the excess suds. When "Sd" is displayed, the washer automatically extends the rinse time to remove the excess suds. During this time, the washer pauses the wash action and adds water for additional rinsing. This pause allows the bubbles in the suds to break. This process is necessary and may occur several times to eliminate the suds.

Concentrated detergents labeled 2x and higher will require a small amount of detergent based on load size. Always follow the manufacturer's recommendations.

Use only HE High Efficiency detergent for BravosTM washers.

Is "Sd" displayed and the wash cycle dial is flashing?

This indicates the washer was not able to clear all the excess suds from the washer. Re-select your desired cycle using cold water. Press Start/Pause. Do not add detergent.

Is "Sd" displayed and the wash cycle dial is not flashing?

If "Sd" is displayed and the wash cycle dial is not flashing, allow the machine to continue running, even if it appears that nothing is happening. When "Sd" is displayed, the washer automatically extends the rinse time to remove the excess suds. During this time, the wash action will pause to allow the bubbles in the suds to break, and the washer will add water for better rinsing. This rinsing process is necessary and may occur several times to eliminate the suds.

Is the drain hose kinked or clogged?

Make sure that the drain hose is not kinked or clogged. Straighten the hose for adequate water flow. Remove any blockage from the drain hose, drainpipe or utility sink. Use the U-shaped drain hose form on the drain hose, and secure the drain hose.

To remove the error display, press Power/Cancel or Pause/Cancel once.

If Power/Cancel or Pause/Cancel does not work:

1. Unplug the washer or disconnect the power for one minute.
2. Plug in the washer or reconnect the power.
3. Re-select the cycle and press Start/Pause.

NOTE: If the error remains on the display, and all of the other questions above have been checked, call for service.

Sorry to read about your problem, I hope this helps you out.

keep unplugged and call for service, so you do not have a fire

I tried to help you. Please help me and Rate/Vote on my response, thanks and good luck

YES

Did you try readjusting the load, or maybe removing heavier items?

Hi and welcome to FixYa, I am Kelly.
My response is very long and will be in 2 parts this is PART 1

Here is what the service manual says about Ld:

"Ld" (Washer is taking too long to drain

water from the wash tub)

Check the following:

Is the drain hose kinked or clogged?

Is the drain hose installed properly? See

"Connect the Drain Hose," page 2-5. Press
PAUSE/CANCEL to clear display
Also:

Is the drain hose clogged, or the end of

the drain hose more than 96? (244 cm)

above the floor?
See "Drain System," page 2-3.
6. To remove the drain pump: (there are 2 pumps... the drain pump is on the left)

a) Loosen the clamps and pull the inlet

and outlet drain hoses off the pump.

Note that there is a tab on the outlet

connector that fits into a slot in the

hose.

b) Remove the three 5/16? hex-head

screws from the drain pump and remove
the pump from the tub.
Check the pump inlet and the tub outlet for obstructions.
Pump electrical winding resistance test:

-Disconnect the wire connector from the

drain pump terminals.

- Set the ohmmeter to the R x 1 scale.

- Touch the ohmmeter test leads to each

of the drain pump terminals. The meter
should indicate between 10.5 and 14 ?.

----Due to the design of the machine the 2 wires going to the drain pump have be notorous for backing out of the plastic connector. Check the connector of the pump for loose terminal connections. --

From the Ld troubleshooting steps / procedure:

Long Drain

Ld flashes when the water level does not change after the drain pump is on.

• Is the drain hose or the drain pump clogged?

• Is the drain hose height greater than 96? ?

• Is the pressure hose connection from the tub to the machine/motor control pinched or plugged?
• Is the pump running? If not, see TEST #7.

TEST 7

TEST #7 Drain/Recirculation

Perform the following checks if washer fails to drain or recirculate.

1. See Activation of Manual Diagnostic Test

Mode, and perform the Manual: Pumps

test.

2. Remove the console to access the machine/

motor control assembly. See Accessing

& Removing the Electronic Assemblies.

3. Visually check that the P4 connector is

inserted all the way into the machine/motor

control.

If visual check passes, go to step 4.

If visual check fails, reconnect P4 and

repeat step 1.

4. Remove connector P4 from the machine/ motor control and check resistance values of pump motor windings. Resistance values should match those shown in wiring diagram, page 7-1.

If resistance values are good, go to step 7.

If winding measurements are much higher (tens of ohms to infinity) than shown in wiring diagram, a problem

exists in the motor winding or in the connection between the machine/motor

control and the motor. Go to step 5.

5. Tilt machine forward to access the bottom

of the machine and the pumps. See
Figure 1, page 6-13.
6. Check the resistance at the pump motor. Remove the connector at the motor and

take measurements across pump terminals. Measurements should be as shown in the wiring diagram.

If winding measurements are much higher (tens of ohms to infinity) than shown in wiring diagram, replace the

pump motor.

If the resistance at the pump motor is correct, there is an open circuit in the wiring between the motor and the machine/

motor control. Repair or replace the lower wiring harness.

If the pump motor windings and machine/ motor control check OK, repair or replace the pump. Be sure to check

the pump and tub sump for foreign objects before replacing pump.

7. See Activation of Manual Diagnostic Test Mode, and perform the Manual: Pumps test.

8. If the Manual: Pumps test failed, then the machine/motor control has failed:

Unplug the washer or disconnect power.Replace the machine/motor control assembly.
Perform the Manual: Pump test.

hi,
usually most areas have a USED appliance store. usually these guys will have a bunch of old fridges and stoves around outside the store. Our town has three or four of them. you may have to ask around but these guys usually have parts for cheap. and they will sometimes make house calls. try googling used appliances in your area. they may also set you up with a cheaper washer with a METAL tub.

good luck
jm