20 Most Recent
Euro-Pro Shark Rapido Electronic Iron - White/Gray - Page 2 Questions & Answers
I love my iron ! How I can use in Israel?
The voltage in Israel is 220 volts. Check the information plate on your iron to see if it will operate on 220 volts. If it will, then you will only need an adapter from the two round pins to a two slot receptacle that you can plug your iron into. If your iron will not use 220 volts then you will need a 220/120 volt transformer with a 1 and one half times larger wattage rating on it than watt rating on your iron. Our iron is 1200 watts. We would need a 2000 watt transformer. On Amazon they cost eighty nine dollars and weigh 29 pounds. And they ship them overseas. Best of Luck
Can't see water level
read you owner manual, and clean the level, for to see the level.In the manual you must have instruction when to add watter.download free from www.retrevo.com or www.fitness.manualsonline.com God bless you
Fire came out of cord conecting to iron got a
The cord has an internal break and it made contact and burned through the insulation, your arm happened to be in the wrong place at the wrong time. Have the cord replaced before you use the iron again. If you happen to touch that bare spot on the cord you could be electrocuted.
I have a Shark iron model number g1579 an it
1.Turn the temperature dial to a setting compatible with the garment being ironed. Set the iron on its heel upright, and allow the iron to fully heat for two minutes prior to ironing.
2.Hold the iron in a horizontal position and begin to iron the garment. When the iron is turned to a horizontal position, it will automatically produce steam. Turn the steam dial to a setting to produce the desired amount of steam for the garment being ironed.
3.Press the water spray button to shoot a jet of water on the garment to help remove stubborn wrinkles. To produce extra steam when using the steam iron, press the burst-of-steam button to release an extra shot of steam during ironing.
4.Hold the iron in a vertical position to stop producing steam. For vertical steaming from the iron, use the burst-of-steam function.
Using the Burst-of-Steam Feature
1.Place the iron upright on its heel. Preheat the iron for two minutes at the maximum heat setting.
2.Place the garment on a hanger away from other garments, and away from people.
3.Hold the iron about 2 inches from the fabric being steamed, and press the burst-of-steam button, pointing directly to the wrinkles. Steam will exit from the soleplate. Wave or move the steam iron over the garment in areas needing ironing while pressing the burst-of-steam button.
4.Stop the steaming by resting the iron in a vertical position on its heel.
Iron doesnot get hot onlyplatform
Try to open the electric iron and locate the thermostat . Secure the electric iron against any metal object that may cause electric shock or short circuit and plug it to a power source. Slowly adjust the temperature and using an electric tester check the power before the thermostat and after the thermostat. If there is a power before the thermostat and has no power after the thermostat then your problem is the thermostat replace it with a new one.
I have a Euro-Pro X
Hi,
I will advice you order for it online, you can order for it at either ebay.com or ereplacementparts.com
My shark iron went into
Hello,
There is probably a disconnection inside the iron that's why it won't light up. Usually, when the heating element get's defective, the won't heat.
If the iron has a three pin socket/plug, open the plug and check if the fuse is intact. If the fuse is intact, then it means you will have to disassemble the iron.
Check all the wire connection inside the iron, observe if you will find any disconnection of any kind. There are not much wire inside the iron, so I believe this shouldn't be difficult.
Have the iron checked by disassembling it.
I hope you understand the above......
Good luck.
I have an older model
Pat, it probably has a calcium scale buildup from lack of use. Try filling the reservoir with a 50/50 solution of White Vinegar and Water and let it set over night (at east 24 hours). Then turn the iron on to the steam setting and see what happens. If it doesn't produce steam, turn the iron OFF, let it cool and soak for an additional 8 hours. After that, turn it ON, set the steam setting and hopefully it will have unclogged. If hasn't after 32 hours, I don't think it will. Also, you can try cleaning the steam jets on the iron's surface, with a firm tooth brush and the vinegar/water solution.
Hope this helps. Please let me know.
I have a Euro-Pro E8000.
Check that the steam holes in the base are clear. There are patent sale cleaners available commercially. Enquire at any major appliance store etc.
Not finding what you are looking for?