Bulova Watch - Answered Questions & Fixed issues

1. Take the watch off your wrist and turn the watch so that the back of the watch is facing up. 2. Use a watch case opener or a small flathead screwdriver to remove the back of the watch. 3. Carefully take out the old battery and discard it properly. 4. Insert the new battery, making sure the plus and minus signs line up with the corresponding symbols in the watch. 5. Securely close the back of the watch. 6. Put the watch back on your wrist and you're done.

Althougj it seems, Its not that difficult. Look for the owners manual forTissot Multifunction Watches PDF (they all work the same way) and follow the steps.

Start with watch in normal clock mode. press and hold bottom right "lap reset" - alarm time appears. Keeping "lap reset" held, I can then toggle the alarm on and off using top right "start/stop".
Qiu: Circle segment lights up (only a black point in the middle, NO ALARM)
Circle segment with a black section on the above middle point, ALARM ON.

The FC 270 does not have a second hand, the red tipped hand points to the month.

www.seikowatches.com/support/ib/index.html

download from accurist web site at
http://www.accurist.co.uk/download/MULTI%20FUNCTION%20CHRONO.pdf

good luck

answered as soon as they are seen. Many thanks for reading Gamecih download for android which is offered for all OS, I mean you could download and install

they cost about $60. they are cheaply made throw away dress watches. you didn't get ripped off. you just wasted your money on cheap chineese garbage, you are not alone. wear the watch, throw it away when it stops or you don't like it anymore.

Thank you for contacting FixYa.
You can find Bulova instructions here:
http://www.bulovaspecialmarkets.com/service/servicecenter.aspx
Jewel

there is no ''adjust'' button?

Send an email to [email protected]. ask for the manual for your watch.Al

I know it's been a while since you posted this question, but I just had to do this with mine after it was lost in a drawer for a few years, and I had no luck googling so I had to figure it out for myself. First, you have to remove the band, but you only need to do this on one end, not both. I did this by twisting the watch body around while holding the cloth/leather portion of the band still, letting the elastic part twist around with the watch body. Then, just use a fingernail to pull on the ridges on one end of one of the pins that are holding the band on; both ends are spring-loaded, so it doesn't matter which. Twist the watch body back around, and you'll now be able to flip it over to expose the back.Now, take a thin, strong blade (I used a butterknife) and pry off the back plate. There's a tab on the upper right edge of the back plate to make this much easier. Since it probably came off in the process, place the rubber sealant ring back around the edge of the backplate.Once you have the back plate off, there's a thin metal piece covering the battery that's held on with one screw. Remove that with an eyeglass screwdriver or any other similarly-sized Phillips-head screwdriver. There's just a small tab holding the metal piece in place on the other side, so just flip the metal piece up a bit and pull it out. You can now take the battery (a CR2016 3-volt watch battery) right out.But wait, what's this? Beneath that battery, separated by a small plastic insert, is another, smaller one, a 377/376 1.55-volt watch battery. The 377/376 powers the analog movement, while the CR2016 powers all the digital stuff and the backlight.Replace both batteries, making sure to place the plastic insert back on top of the 377/376 before putting the CR2016 back in, and follow the steps in reverse to put the watch back together. You may have some difficulty getting the back plate back on, but I just pressed one side in and held it while I tapped the other side down with my fist.

Watch cases and bracelets are cleaned in ultrasonic cleaning maschine with the help of special clening liquids.
Mechanical watch movements and mechanical parts of quartz and analog watches are cleaned in special watch cleaning maschines in 3-5 cleaning stages and cleaners.
Electronic parts, circuit boards, LCD screens are cleaned by hand using specialy made cleaning solutions for each individual part.
To do all this you need a watchmakers skills as the watch must be disassembled completely.
Do not forget to rate, please.

Your watch thinks your noon is midnight.

Wind the hands forward 12 hours and the date change will be at midnight. You will have to re-set the date if it gains a day when doing this.

My watch is OTS T6320G ,kindly advise as I want to fix time and date

J'ai besoin d'un manuel d'instruction en fran?ais pour ma nouvelle montre ?ve Mon crois N303

Yes, Bulova used M0 to indicate the year 1960, but the marking on the case may not necessarily match the movement. It is not uncommon to find a movement that was produced one year earlier or one year later in a case made for the model. So, although the case of your watch was produced in 1960, the movement may be from 1959 to 1961.

While holding the light button on press the mode button once. Changing the time process will then begin.

What is your question?

how do I reset a Casio lap memory 50 or 60 watch