20 Most Recent Maytag MLE24PDAYW Dryer Commercial Dryer - Stack, Electric, Microprocessor Controls" - Page 5 Questions & Answers

i don't know. most dryers come with a chart showing what wires are for. green is usually used for ground but read your chart. few have chart with owner's manual and most i have seen are in a clear plastic bag stuck on the back or stuck in the open area under the tub.

Nothing happens when push start button. All limits are good. Element tests at .001 ohms.

Check the igniter it should glow when turned on

I don't know what it means but you can try to reset the control panel by unplugging it for 10 minutes then plugging it back in. This may or may not help but it works every time my dryer gets stuck on or off with the panel display showing something odd, or stuck on so many minutes left but it doesn't ever stop. It won't cost you anything to try this. If it happens very often you may need the panel replaced.

I'm having trouble finding the exact capacity of your dryer, but I believe it is around 7.0 cu ft, which is about as large as you can get in a standard-width home dryer.

Most likely cause is a thermal fuse or the heating element. And if it's a thermal fuse, you need to make sure the dryer vent is clear and un-restricted, since that is the most common cause of thermal fuses blowing.

be very careful with electricity. fuses are in the home's wiring. open the dryer door. if possible follow the wire from the large plug back to the home's main electrical panel. there may be a small panel just for the dryer or it may be connected directly into the main panel. locate the fuses if used, unscrew them and replace them with ones you know are good or use an electrical meter to test the original fuses for continuity. install good fuses. if your system uses circuit breakers, locate the breakers and look to see if they have been moved from the on position. switch them off and on a few times and leave them on. go and close the dryer door and choose a new dryer setting to try to see if your dryer works. great if all works as it should. if dryer won't start or fails again, you need to have your house wiring inspected or your dryer repaired. call for help without delay.

i don't know. consider shutting off dryer, open the dryer door, turn off the main electrical source [shut off circuit breakers for dryer or unscrew fuses. shut the dryer door and turn breakers on and or fuses in. this may reset your machine's internal program. choose a new timed setting to see if all is OK.

It may seem crazy, but you have to remove the dryer door, and then take the door apart to be able to replace the handle! I've tried doing it without taking the door apart, and I only ended up damaging the door and replacement handle!

Hope this helps https://www.youtube.com/watch?v=x-Rc0dKCiuw

I did A & B, B actually did the trick and I have had absolutely no problems. Possible Solutions A Power unit down by turning off the circuit breaker(s) for one (1) minute.

1. Power unit up by turning on the circuit breaker(s).
2. Start a time dry cycle.
3. Monitor the dryer for one (1) minute to ensure the error code does not display again.

B It indicates that the lint screen or vent is clogged; the vent is crushed, kinked or has too many turns. ... The dryer will continue to run when this diagnostic code is present. My dryer did the same thing. I cleaned all the vents thoroughly, if you are unable to clean inside where the vent screen is try this. remove lint screen, using tape or rubberband attach a empty paper towel roll to the end of your vacuum crevice tool. Also at the 99 cent store I purchased a appliance brush to loosen any lint inside before vacuuming. The brush works better then the one I purchased from Home Depot for $15. Vacuum the inside of the dryer, be sure to vacuum the very back inside and around the door. This is the tricky part now. The dryer flex hose actually has to be set just right. If the placement is incorrect you will get the error codes, dryer turns off after mins etc. Here is a Flex hose tip video. Hope this is helpful

if you are turning it from the inside of the dryer with ease then check to see if belt broke.

Only thing that comes to mind is,  it may be in "advertising" mode

Try Pressing the damp dry and sensor dry keys
for 5 seconds will take it out of the 
Advertising mode.

(In Advertising mode No functions will be run
except illuminating the LEDs.)

Check you flame. If the flame is very short (less than half way down the burner tube, it can be a gas pressure regulator failure. They are adjustable but that usually indicated it is about to fail. Make sure the flame ignites every time you hear the relay and solenoid valve click. The is a small panel on the front that can be removed to see the burner and the pressure regulator. The is a glow igniter that comes on several seconds before the gas is admitted. Confirm that works. Check at the dryer vent whether you smell gas once and a while which would be an indication of a failure to ignite.

have you checked the relay for the igniter and confirmed there is power to the igniter?

Check "repairclinic.com"

is the flame in the burner tube impinging on the cutoff? This can happen if the burner tip is dirty. The flame can then be asymmetric in the burner tube.

There are two coils on the gas valve that fail from time to time. Before changing them, check to see if you can light the burner by using something like a bar b q lighter or a long match as soon a the igniter switched off to confirm whether the gas valve is working. I have had the same problem and had to replace the coils on the gas valve. One of the coils is an opening and the other is a hold coil.

Failure to start spinning is usually caused by the door (safety) switch not working. Depending on what you broke off, you may have to replace the whole switch

The problem is likely the timer contact failure