Top 20 Invicta Subaqua Noma Iii S Questions & Answers

watch shops and jewelers sell wrist bands

Pull the stem out 2 clicks sets the time, pull the stem out just 1 click turn it forward sets the day and turning the stem backwards sets the date. I hope this helps

Check this post out.. it may fix it. in my case however, it worked in position 1 and not position 2. https://www.keepthetime.com/blog/how-to-set-an-invicta-chronograph-back-to-zero/

It isn't stuck.. it just isn't working... yes you need a battery

you can find what you need at Invicta Web-site http://invictawatch.com I had order straps from them for my Sabaqua NOMA III and russan diver here is also the link for the service http://www.invictawatch.com/support_files/service_center/ServiceCenter.htm

Good day I had purchase parts direct from Invicta and found that is easier then looking around for the parts here is the info; Message Invicta Customer Service . Mon - Fri . 9am - 5pm EST Email [email protected] Call 800-327-7682 . Mon - Fri . 9am - 5pm EST Fax 954-921-2508 or 954-862-5461 Write Invicta Watch Group Attn: Customer Service One Invicta Way (3069 Taft St.) Hollywood, Florida 33021 U.S.A. #PS or you can also check them at their web-site http://invictawatch.com most parts are really low cost with the exeption of the mechanic parts

go to this website www.infixta.com

I will trade you my steel one if you have a blue rubber one.

I have an invicta subaqua noma 3 model no.0736 that I am trying to replace the bracelet/band and would like to know how to change it , how many screws do I remove and what screws do I remove, can you help me?

I have had the same problem with one of my SANIIIs, As you have probably figured out, there are two small screws that are part of this assembly, lower one is the pivot point, upper is the latch. There are also very small rubber bushings (upper & lower) in the pivot of the crown protector, if they are worn it will present side to side movement or "slop" they need to be replaced in this case (I Just went through this on an older Valjoux 7750 SANIII - same problem, latch would not stay closed), you can order the part from Invicta or take from a donor watch in the mean time (Invicta will take several weeks to months to fulfill a part order) The upper screw goes through a small cylinder or cam, there is a little (very little - but it is there) to move that cylinder outward towards the upper pusher or top of the watch. After you loosen the top screw (loose not remove) you can adjust this play w/two precision screwdrivers, one to tighten the upper screw one to lever the cylinder toward the top of the case by leaning one screwdriver w/ just a slight pressure against the crown and the cylinder to widen the area between the pivot screw and the latch cylinder. Don't overtighten the screws to try to add friction to the assy - the threads & heads are fragile, you can damage the case or strip them - or worse snap the head off. Hope that helps.

you cannot fix this. Unfortunately for movements to be that exact they cost a lot of money and the movement inside your subaqua is not that high tech and accurate. This is what makes watch really expensive the little things like this. Unless you are buying a 10k watch , they usually are not going to have the top of the line movement . The movement you have in your watch is an ISA 8173 and that is as accurate as the watch will get.

It has an automatic movement powered by the movement of your arm.

mcdevito75 here, Your invicta may have a screw down crown that adds water proof protection to your watch, try to un-=screw the crown when un- screwed then pull up to set time.

Easier than you think.Pull your Crown out to the FIRST stop (were you would normally set your date). Push the "A" button (top chrono button) for your dial at the "3 oclock" area, Push the "B" button(bottom chron button) for the second hand.

mcdevito75 here, BEST BET, if you have a warrantee with Invicta, contact them for repair. If not look for a small watch repair shop in your area.

It should never move unless you initiate the timing with the upper right hand button.

Easier than you think.
Pull your Crown out to the FIRST stop (were you would normally set your date). Push the "A" button (top chrono button) for your dial at the "3 oclock" area, Push the "B" button(bottom chron button) for the second hand.

Watches either have screws in the links that you can remove to remove a link. Or they have a pin in each link that you must push out to remove a link. Some have a "hairpin" looking keeper that you remove. Hope one of these will work for you. Good Luck

What 3 screws? Give me: Make, model, all the numbers on case back. Explain in detail what 's wrong. Where screws are/were located and so on.

Check out my TIPS here and you will find out how to do that