Fisher and Paykel WA37T26G Top Load Washer - Answered Questions & Fixed issues
Hi, I have a fisher and paykel washing machine
to work out the fault code go from right to left far right light is 1 the next is 2 next is 4 then 8, then 16,32,64,128. add up which lights correspond to your machine and then you can google that code and find what your problem is
10/26/2017 1:53:46 AM •
Fisher and...
•
Answered
on Oct 26, 2017
•
202 views
Fisher Paykel washer repair
it will be the pump. just check again where you did last time. there may be something in the hose, coins can get stuck, and lint. check also the pump is not getting very hot.
8/12/2014 8:05:55 AM •
Fisher and...
•
Answered
on Aug 12, 2014
•
304 views
Repair manual
This is the user manual.
http://www.fisherpaykel.com/vault/pdfs//pdf_usecares/4112_US_Ecosmart_Washer_EN_FR_UG_lo_0109.pdf
6/6/2014 8:05:11 PM •
Fisher and...
•
Answered
on Jun 06, 2014
•
344 views
Flashingho
the lights are a fault code, this will help with diagnosis. check your motor for corrosion.
12/21/2013 8:49:46 AM •
Fisher and...
•
Answered
on Dec 21, 2013
•
41 views
Fisher and paykel gw712 will not spin
That is fault code 43
43. (00101011) Phase 1 to 6 - OOB Switch Fault
The Motor Controller module has found that the signal returning from the out of
balance switch indicates that the switch is permanently on or the harness to it is
disconnected.
Primary Source: Mechanical.
Action:
1) Check that the out of balance switch is free to move.
2) Check that no harnesses are blocking switch movement.
3) Check that the switch operates correctly when activated. Replace the switch
if suspect.
4) If the out of balance micro switch shows signs of corrosion, replace the
switch and switch harness, and fit a condensation kit to the console area if
not incorporated in the top deck.
5) Check the level of the machine and also the bias spring.
Secondary Source: Wiring.
Action:
Check the harness to the switch is connected correctly. The terminals should be
connected to the normally closed position. If the harness terminals show signs of
corrosion, then fit a new harness.
12/18/2013 12:05:21 AM •
Fisher and...
•
Answered
on Dec 18, 2013
•
144 views
Machine won't turn on
That sounds like the pump is jammed and did not pump all the water out.
12/17/2013 11:24:50 PM •
Fisher and...
•
Answered
on Dec 17, 2013
•
124 views
Fisher and Paykel Aquasmart
250. (11111010) SmartPump Loss Of Sync
This fault is normally as a result of the pump not starting. This fault is usually caused by an
object that has gotten into the pump, and is either under or on top of the impeller, which is
causing the motor to stall when it is trying to start.
Primary Source: Pump Stator Windings Open Circuit.
Action: Measure the resistances of the pump stator. For more information
refer to the AquaSmart service manual.
Secondary Source: Pump System.
Action: Follow procedures as for Fault Code 249.
Tertiary Source: Motor Control Module.
Action: Replace Motor Control Module.
12/17/2013 11:10:07 AM •
Fisher and...
•
Answered
on Dec 17, 2013
•
513 views
My machine wont power on. I checked the outlet and
you have blown the fuse on the main board. you will need to check short circuits in your pump and motor, and for leaks onto any electrics, and then replace the motor control board (or try to replace fuse on board if other components look fine ie no burn marks)
11/12/2013 8:47:34 AM •
Fisher and...
•
Answered
on Nov 12, 2013
•
121 views
Add clothes evenly, turn on get no water, water
sounds like a valve fault. this fault can be caused by the electronic board not powering the valves also. check power to valves during fill, if power, replace valve. if no power replace board.
11/12/2013 8:39:56 AM •
Fisher and...
•
Answered
on Nov 12, 2013
•
54 views
Water leaks from bottom when filling
have you got the hot water pipe on? the water can sometimes flow back out this valve if it is not plugged. has it been serviced recently? there is a pressure pipe that attaches to the side of the bowl, and a pump that need to be secured or you will get a leak from the bottom. if is has become loud on spin recently, it could be that you have a leak from the main seal, and will need bearings replaced aswell, but that model seems a bit new to need bearings already, but it's not impossible.
11/11/2013 10:43:50 AM •
Fisher and...
•
Answered
on Nov 11, 2013
•
191 views
Not finding what you are looking for?