20 Most Recent General Electric DBXR463EG Dryer - Page 5 Questions & Answers

There is one available here

Whirlpool 8544945 Part Number : Knob, Timer (Silver)

Unlimited Appliance Parts https://www.unlimitedapplianceparts.com > 8544945-... KNOB ASM - DELTA/HD, WPL. US$28.81 All the rest say discontinued. https://www.google.com/search?q=WPL-8544945 ..

The screws and spacers for the device are lost. However, the mounting hardware could easily be replaced by three screws and corresponding plastic bushings/spacers. Unfortunately, I could not find any information about a fuse for this device. If you're still experiencing issues, I recommend contacting the manufacturer or a certified repair technician.

Depends on what and where the wires are plus what they feed.

Could be due to multiple reasons, from too much a load to the heating element being faulty. Here are some addressed. Replies get better if you post the brand and model of the machine https://www.whirlpool.com/blog/washers-and-dryers/dryer-not-heating.html .https://www.youtube.com/watch?v=S9KaJeV_bMQ https://www.mrappliance.com/blog/2019/april/dryer-not-heating-up-here-s-what-to-do/

Two Beeps on my Bosch WTE84100au Condensing Dryer means a thermal overload but also means one of the thermal sensors is faulty .... as if it is always on. Open the door, pull out the lint catcher and clean around the silver probe (it's like a shiny 1/8" nail sticking into the cavity below the lint catcher). If it still doesn't work (and still 2 beeps), just flick it lightly a couple of times. If it still doesn't work, flick again from the other direction.

Not much in the way of diagrams https://www.google.com/search?q=casablanca+claremont+ceiling+fan+49gxxh+parts+diagram This shows what the receiver looks like https://www.google.com/search?q=casablanca+claremont+ceiling+fan+receiver+replacement ..

Model STFT-16H

Check light wire in ceiling to make sure it didn't come loose.

Check your vent duct or filters for excess lint. Also dryers are protected from incorrect settings and pressing the On button for too long or just briefly. Try a full second.

This should work for you. XEFLOOR420 - MaxxAir HVFF 20 & HVFF 20S Motor/Switch/Cord Assembly - USFanco

yes, but they are normally fixed inside with crimped connectors. Easier to make the hole bigger and put a plastic cable plug in it, or cut the plug off and wire a new one. https://www.google.com/search?q=Counter+top+wire+access+plug and https://www.amazon.ca/Replacement-Connector-Industrial-Straight-Grounding/dp/B08C76KJF7/?th=1 ..

is there an on/off for the light?

probably clogged vent and/or lent filter. Worth removing top and looking inside as well. May need a good vacuuming out.

to properly clear, diagnose the code and remedy the issue. Code will then clear.

check door for debris or blockage around latch. sounds like door either isn't closing all the way or sensor isn't reading it's closed.

My answer Edited 7th October 2023 as the website links mentioned back in July 2022 now fail. This new link states Harbor Breeze is an exclusive Lowes product now, not sure it it was before, but they are also sold at Home Depot. https://harbor-breeze.pissedconsumer.com/customer-service.htmlThere are a number of copycat and deceptive websites mentioned in this question, and I deleted one Answer that was purely and advertising click thru site and nothing more than that, with no support information at all.Do your homework check the small print.This website is helpful but not Harbor Breeze support.https://yourceilingfan.com/harbor-breeze-troubleshooting/harbor-breeze-ceiling-fan-wiring/..

'contractor'? or 'contactor'? https://www.google.com/search?q=Unimac+dryer+is+giving+a+fan+contactor+error .

You use a 4 prong grabber tool. They are flexible https://www.amazon.ca/Housolution-Magnetic-Four-Claw-Bendable-Flexible/dp/B07NWDXF1Z/ref=asc_df_B07NWDXF1Z/?tag=googleshopc0c-20&linkCode=df0&hvadid=335609670434&hvpos=&hvnetw=g&hvrand=7258136797482333435&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9000812&hvtargid=pla-664439408842&th=1 Otherwise you remove the case and remove the drum on your unstated mystery make / model. ..

I have something that fell into the lint trap and is under the drum! So when I turn it on I hear something hitting the drum scared it's a lighter and might blow! So how do I open to get to grab what's under the drum?