20 Most Recent
Toshiba E-Studio 3511 Color Copier - Page 6 Questions & Answers
ERROR SAYS PAPER STUCK IN
Good day!!!
Please Check the following:
- If paper doesn't feed, remove it from the sheet feeder. Reload it
against the right side, behind the tab, then press in the tab on the
edge guide and slide it against the paper and make sure it's not too
tight. Make sure the paper is not above the arrow mark inside the edge guide.
- If multiple pages feed at once, remove the paper from the sheet feeder, fan the edges to separate the sheets, then reload it.
- If you're printing on both sides of the paper, try loading fewer sheets.
- If it's wrinkled when it ejects, the paper may be over-saturated or
too thin. (If the paper is over-saturated, make sure you select the
correct media type in the printer software).
- Make sure you use new, smooth, high-quality paper, that is not
curled, creased, old, or too thin. Make sure to load it printable side
up.
- Do not load paper with holes punched in it.
- Do not load paper that is too thick for the printer.
- If paper is jamming when you are inserting only one or two sheets,
try loading more pages at a time. However, do not load more than the
recommended number of sheets.
Paper type
Load up to
this many sheets
Plain paper
100
Epson Bright White Paper
Epson Presentation Paper Matte
80
Epson Premium Photo Paper Glossy (4 × 6 inches only)
10
Epson Photo Paper Glossy
Epson Premium Photo Paper Glossy
Epson Premium Photo Paper Semi-gloss
Epson Premium Presentation Paper Matte
Epson Premium Presentation Paper Matte Double-sided
Epson Photo Quality Self-Adhesive Sheets
Epson Iron-On Cool Peel Transfer paper
1
Note:
3-hole paper, transparencies and vellum paper are not supported.
I hope it helps you...Please testify or rate me when you find it somewhat helpful Thank you and good luck.....
Have a konica minolta biz
Hi,
This is h
ow to reset failure codes (F34, F35, F36). To reset failure codes, perform the following steps:
- Enter the 25 mode (turn the machine ON, while pressing the 2 and 5 keys).
- Select [1. software SW settings]
- Using the arrows on the left of the touchscreen scroll to DIP SW 3.
- Using the middle arrows scroll to BIT 1.
- On the touchscreen select OFF (0).
Hope this resolves your issue. Thank you for using Fixya.
I have a toshiba e
[C580] Communication error between IPC board and finisher
(1) Check if the specified finisher is attached.
(2) Check if the harness connecting the IPC board and the finisher controller PC board is disconnected
or open circuited.
(3) Check if the conductor pattern on the IPC board is short circuited or open circuited.
(4) Check if the conductor pattern on the finisher controller PC board is short circuited or open circuited.
(5) Replace the IPC board.
(6) Replace the finisher controller PC board.
Toshiba e studio 3511 F120
F120] Database abnormality
(1) Rebuild the databases. (Perform 08-684.)(2) If the error is not recovered, initialize the HDD. (Key in "2" at 08-690.)
Any money the HDD is duff. Srri
E-Studio 3511 Color Copier written in the screen
hello
we have like that message before in our copier also but the only thing i did is shutdown and start again and i reset the counter and it goes fine.
make hard reset remove all the power cable and plug again.
thanks
We have a toshiba e-studio
try making the ip on the machine the last 3 numbers 250 if there is no ip confict add a new port in the print driver with the new ip if you do not know what the computers ip is go start,run type ic cmd press enter and the in the window type ipconfig /all that will give you the ip config of the computer. if there are not to many computers on the network check all the pcs and pick a ip add that is not used by the pcs and give it to the copier
When we make copys, the
Have you removed the glass and cleaned inside the scanner ? If the lamp or mirrors in the scanner are dirty, or hazy, that will cause the problem you are having.
And yes if they are clean them most likely the lamp is bad. But try cleaning the scanner well first.
How do i print an
Unfortunately, bad choice, e-studio 3511c is not capable to print on envelopes, that is why you can't find option in printer driver.
Not finding what you are looking for?