20 Most Recent
Toshiba E-Studio 3511 Color Copier - Page 8 Questions & Answers
Error ce20
Hi how are you this is jack ...
[email protected]
Dear follow the procedure...
[CE20] Image quality sensor abnormality (no pattern level)
1. Check if the transfer belt or transfer belt unit are securely installed.
2. Check for any abnormal stain caused by poor cleaning, large flaw or break on the transfer belt
surface.
3. Check if the drum and the transfer belt are rotating. If any abnormality is found, correct any
mechanical problem.
Is the connectors CN345 on the LGC board disconnected?
Is the connector of the image quality sensor disconnected or the surface of the sensor stained?
Is the harness between the LGC board and the image quality sensor open-circuited?
Is the shutter of image quality sensor opening and closing normally? Is the shutter damaged?
PLEASE VOTE ME.
Thanks,
Best Regards,
Lost my admin passcode
Hi how are you this is jack..... (
[email protected])
Dear follw the procedure..
1 you press 0 and 8 key simantenesly and copier ON other Hand.
2 When copier windows show CHECK TOTAL COUNTER .
Then you press 263 and start key.... copier show a new windos.
Copier show YOUR OLD ADMAN CODE/PASSWORD.. Then you
READ HEAR AND CHANGE HEAR... PRESS ENTER KEY..
copier off.. and simple ON..
PLEASE VOTE ME..
Thanks
Best Regards,
Misfeed in copier error E200
Hi how are you this is jack my personal ID
(
[email protected])
Paper transport jam
[E200] Upper drawer transport jam (not reaching the registration sensor)
Open the jam access cover. Is there paper in front of the registration sensor?
YES Remove the paper.
NO
Is the registration sensor working? (Perform the input check:
NO 1. Check if the connector of the registration sensor is disconnected.
2. Check if the connector CN345 on the LGC board is disconnected.
3. Check if the connector pins are disconnected or the harnesses are open-circuited.
4. Check if the conductor pattern on the LGC board is short- or open-circuited.
5. Replace the registration sensor.
6. Replace the LGC board.
YES
Are the upper transport clutches (high/low speed) working?
NO 1. Check if the connectors of the upper transport clutches (high/low speed) are
disconnected.
2. Check if the connector CN362 on the LGC board is disconnected.
3. Check if the connector pins are disconnected or the harnesses are open-circuited.
4. Check if the conductor pattern on the LGC board is short- or open-circuited.
5. Replace the upper transport clutches (high/low speed).
6. Replace the LGC board.
YES
1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and
replace them if they are worn out.
2. Check the transport roller. Replace it if it is worn out.
Thanks
Best Regards,
Error c446
Hi how are you this is jack hear in pk ....(
[email protected])
First Step copier ON 0+8 press 400 press start Baton.
copier show one value ...5or 6 or7.. any xyz then you press 0 and enter... copier off... simple copier ON....
Thanks
Best Regards,
The alignment for the touch screen is off
hi how are you this is jack hear in pk........
First step.... copier on 0+8 and enter 692 press start ...
copier scree show two CRASS one upper side and second lower
side .... you tech pen tip middle side on the both CRASS ....
copier off....
simple ON.... (
[email protected])....
Thanks
Best Regards,
Misfeed in the in the automatic duplexer
open automatic duplexer door you will see 4 parts to open and green ring for rotating. rotate it the jam paper it will removed. or open all 4 parts you will see the paper if not open drower and remove the paper jam,
What about printing envelopes??
Most copiers will not do envelopes. Sales people say they do and they may do one when it is Brand New. Most copiers are not designed to handel them in the paper feed units. What you can try is to use the manual by pass tray. It will be the best chance, it is a straight shot though the copier. Good Luck
Toshiba 4511 error CEF0
CEF0 indicates Revolver motor abnormality.
Perform output check 03-450 whether the revolver motor is working. If not, then change the revolver motor. If working, then u probably need to change the DRV board or LGC aaboard.
*Make sure all the connectors are plugged
Toshiba printer copier
If this only happen for copying, but not printing, then is the scanner unit problem. Shut down MFP, take out the big mirror, clean the mirrors and exposure lamp.
How easy is it too fix an F100 problem
f100 indicates hardrive problems.
power off machine,
power back on while holding down 0 & 8 on number keypad until beep is heard,
enter 690 on number keypad,
press start,
enter 2 on number keypad,
press yes on display and wait for machine to ask for reboot.
be patient may take a while and if it doesnt work could be hard drive failure.
if it is the hard drive it could also mean updating firmware on hard drive and machine.
Not finding what you are looking for?