20 Most Recent Toshiba E-Studio 3511 Color Copier - Page 9 Questions & Answers

C360 indicates Charger cleaner motor abnormality. Make sure the charger unit is installed & engaged to the drive gear. It is a common problem on e3511 model, where the main charger unit will loose.

These copiers have serious toner dust issues. Light copies are usually caused by dust in the optics (the mirrors) and on the laser glass.
Take off the main copy glass and gently clean all the mirrors and scan bulb underneath it - be careful.
If you remove the drum unit and look inside the cavity you took it out of you will probably find a huge toner mess. the laser glass is situated in this cavity and needs to be cleaned - just clean whatever you can see...

check to make sure on the display panel the paper tray is showing A3 PAPER SIZE>> the paper size indication should match up to what is in the trays if not the machine will be asking for A3. Also try putting in another tray to see if there is a fault with the paper tray .. if it works with other paper sizes it may just be the size hasnt been set properly for that tray.. Hope this helps A

There are a lots of handbooks for each series. Normally is only released to distributor, not for consumer...

Once u place the envelopes on the bypass, u need to select the "envelope" paper size.

Yes u can. There are 2 file types available, TIFF and PDF.

Well, since the MFP is big & heavy, u can separate out the RADF and duplex unit. If still heavy, u can take out all the process units.

CA20 indicates H-Sync detection error.

U need to check whether the cable (flexible flat type) between the connector (CN334) on the LGC board and connector (CN201)
on the LDR board open circuited, broken or disconnected. Try to replace another cable.

find here---- http://eu.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp

Once u setup the drawer paper size, make sure u tick the update automatically on the printer driver properties. Otherwise the printer driver wouldn't detect the correct paper size.

How do u get in service mode on a toshiba 3511

this copier doesnt have fuser oil so you dont need to-it uses oil impregnated rollers.

Drivers for Win 7 are not provided by Toshiba. But you can try Vista drivers; they may work as well.

Please navigate to copiers.toshiba.com.

On the top of this page, click on SUPPORT & DRIVERS. Just click on it, no need to choose anything from the dropdown menu.

On the next page (after clicking on support) look for Enter product name or number.

In the text box type e-STUDIO3511 (or just type 3511) and hit search.

The next page lists all the drivers.

If yopu are unable to download, I can upload them to an external server.

Waiting for your reply.

format hard by power on+0+8 then 690 then start then2 then set then report the mashin or revision the logic may be there is a problem in it

Open the front panel. There is a power stitch there...

Hi.


Do the following procedure:

1. Turn off the copier.
2. Hold down the "0" and the "8" key and turn on copier at the same time. Keep holding until you hear a beep (about 8 secs).
3. The machine will enter diagnostic mode .
4. Enter "653".
5. You will be asked to enter a new 5 digit code
6. for administrator.
7. Chose save on menu.
8. Turn off copier and restart.

Use the new admin password to set up the other accounts.


Regards.

Yes you need to emulate the driver or revert back to your old OS as the print driver is not yet released for snow leopard.

I would not lie to you as a toshiba tech they have not made a update yet to support leopard 10.6 you have to downgrade to 10.5 or lower.


please do click the accept button Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

C448 means you have a fusing unit malfunction. The fusing unit is the part that gets hot just before the paper comes out of the machine. You can try clearing the code using this reset procedure:
(1) Turn the power ON while [0] and [8] are pressed simultaneously.
(2) Key in "400", then press the [START] button.
(3) Change the displayed current status counter value "32" to "0", then press [ENTER] or [INTERRUPT] (to cancel C448).
(4) Turn the power OFF and then back ON.
If the code comes back you are going to need a fusing unit.

quote is probably in the right price range. you need to look at how many copies are on your machine. look at any future repairs/supplies that will be needed. like drum, developer unit. If these are also needing to be changed soon, you will have to plan on those costs also. Any comparable machine that you get get will be expensive to repair the big items. You have to put all of the money that you spent on the machine and find out how many copies you have made. you can then figure out the cost per copy. At the same time, if this machine does everything that you need from a copier, do you want to buy a new one at much higher cost.