20 Most Recent Toshiba REGZA 52RV530U LCD TV - Page 4 Questions & Answers

Hello,

All plasma an LCD TV have boards that control vertical and horizontal output to their respective areas. They are connected to the screen by ribbon cables. If one of these boards fails all together, has a failed chip, a bad connection, or a bad ground somewhere it will result in a black line in the area of that board. A bad ribbon cable connection on the bottom will result in a vertical black bar though the screen. Many times resetting the connection will fix it, if the ribbon cable has been nicked there could be a severed connection. They an sometimes be fixed, but it is a pain. An yes I have done it, but the bar is gone. The same will happen if the chip that outputs to that area opens. The connectors are the first place to look paying close attention to the cable, they are extremely delicate so great care must be taken if you decide to tinker with em, the usually have lift locks that release them, but it is very easy to wreck em.

Good luck.

Aparently your LCD driver board is going out on you and you going to need it to be repaired the genral estimate for cost for the part in question is $150 respectivly labor not included. Most people can take care of this on there own so that option is on the floor for ya. The partstore.com and mateletronics.com are the two best parts places on the internet in case you want to fix it on your own.

Please do be considerate of my time here when you press the accept button, Thanks for using fixya.com and for being a valued customer. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

You may have lost the 24vdc or bad inverter board but you need to do some voltages checking first.
Please see my basic troubleshooting guide here:
http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide

http://s807.photobucket.com/home/budm/allalbums

http://en.wikipedia.org/wiki/Capacitor_plague
Parts: www.shopjimmy.com

This is something wrong with the t-con board, T-con board is a part of the panel, the part # is not available, but the Panel mode is LTA520HB0, part # 75011258 cost approx $3,210.13.
If you need more information, please write it down here.

This is a catastrophic and known failure of older Toshiba sets, not much you can do, try to take out a retrospective extended warranty, wait a month and claim, good luck.

This is the best solution for your problem as a 40 year experience with wires etc. Go to the source of your cable signal connector . Open it and clean the terminals with emery paper , sand the end of the cable shiny clean from corrosion , get a new barrel connectors with gold terminals if possible lengthen the ends of the cable , insert and tighten good, use thick rg-16 or rg 40 cable with good insulation ends crimped professionally with a crimpier or buy ready made , not from dollar store. Get a gold plated professional splitter if you need one or two , it will cost about 15 or more each . Make the cable runs as short as possible, using the thick good cables. If needed get a signal magnifier. From radio shack or the source etc. Connect them good and tight . Ground the splitters . Problem solved , you will get crystal clear channel 2 to 7 including 3 and 4 . Isolate the TV cable from other cables and power wires. Vitally

Sounds like you have a Tcon fault.Only if you are competent to carry out this procedure then follow the task below.If not, always get a qualified Tv engineer to repair the TV.
Remove the back cover from the tv. Located top centre on the LCD is the Tcon board which is encapsulated by a metal plate. There is a lead attached to the Tcon which is held on my 2 lugs either end.Gently squeeze the lugs inwards and remove the plug. Next clean the contacts gently with a fibre pen..or a pencil rubber. Insert the lead back in the Tcon gently as the plug is delicate. Try the TV and see if the lines have disappeared. If not, check the connection at the main board and try again. If this doesnt cure the fault, then you will need a new Tcon board.

First thing to check is the picture size. You can view many program formats in a variety of picture sizes

1. Natural
2. TheaterWide 1
3. TheaterWide 2
4. TheaterWide 3
5. Full
6. 4:3 HD
7. Native
8. Dot by Dot.
   

The format of the image will vary depending on the format of the signal you are currently watching from you cable or satellite provider. Select the picture size that displays the current program the way that looks best to you.

To select the picture size using the remote control:

1. Press I on the remote control.
2. While the Picture Size screen is open, you can do one of the following to select your desired picture size:
   

• Repeatedly press I.
• Press the corresponding Number button (0–6) while the Picture Size screen is open.
• Press B or b while the Picture Size screen is open.

To select the picture size using the menus:

1. Select Picture Size in the Theater Settings menu.
2. Press C or c to select the desired picture size setting.
3. Highlight Done and press T.
   

Some of the picture sizes may not be available depending on the receiving signal format from your cable or satellite provider (those will be “grayed out” in the Picture Size screen).


Second thing to check is the Native Mode which restores the size of the picture by the 3-5% that is generally lost during the normal over scanning that occurs on traditional sets. It also avoids unnecessary scaling of 1920 x 1080 HD signals. I hope this helps and good luck!

To start with use 800x600 32 bit.

not a chance you will end up destroying it. Ups or FedX never have a problem shipping anything

Hi there,

Well it's hard to find the screen separately anyway you can contact to Toshiba and ask them for the screen, Follow the below link to contact Toshiba  -

 http://www.toshiba.com/tai/

Good Luck!!

Thanks

Hi.

Please follow thoroughly the instructions below, click on the picture to enlarge:



Instructions and pictures are the right ones for your model. The had been taken from user manual. To access the screws you have to remove the back panel cover.


Instructions are also available at page five of the manual. You can get the full manual clicking on the link: 52RV530U Integrated High Definition TV.

Please do not forget to leave feedback.

Best regards.

G.

Check to see if the tv is in the text mode of the closed captioning.If not you may need a new main signal board.Also try unplugging the set for a couple of hours to reset it.

You could as the part number for the panel is 75011258. However it runs about $2500.00...Your best bet is to replace the TV.

on the back of the set near the stand there is 2 - 4 screws just unscrew them, you will need to giv the pedistul a good tug but it will come of :D

Good wireless headphones have "line in" cable with 2 RCA plugs, which must be attached to TV's "audio out connectors. If you have only "optical" or "coaxial" audio stream out, you must upgrade your "wireless" gear to accommodate those signals. Forget about "headphone" jack! It's a blast of the past!Thanks,Alex.