20 Most Recent
HP LaserJet M1522nf Multifunction Printer (CC372A) - Page 2 Questions & Answers
HP Laserjet M1522nf - displaying
this error can be caused by a paper jam, or a little piece of paper in the toner area, Take the cartridge out and use a flashlight to check in the sides looking for paper. Other reason is that sometimes the sensor that detect the toner is out of place and in that case you can try to power cycle with the toner out before you install it again. Good luck
Tengo problemas con un Multifuncional
Hola amigos, tambien tengo este problema con una impresora, reinstale el firmware y no funciono, lo que note es que el motor estaba quemado, lo desarme y lo rebobine, compre el alambre me parece que fue calibre 33, aprox 25 mts, 260 vueltas con una resistencia de 10ohms por bobina. bueno despues de esto lo monte y funciono un poco mejor. pero al parecer es la tajeta logica pregunte a un proveedor de hp y su valor es de aprox 3000 pesos mx, lo que hice es hacerle un agujero al escaner. Detalles. viendo de frente el escaner del lado izquierdo le hice un agujero de 3mm. y le puse un cincho largo(pueden usar algun desarmador, el cincho se lo puse doble para que no se doblara, el cincho debe entrar con facilidad pero no muy olgado para que no se doble, al introducirlo no es necesario sacarlo ya que el carro lo sacar, es por eso que no debe quedar apretado). esto me permite mover el carro del escaner a lo posicion "0". posicion de partida y hubicacion de la banda indicadora(Empujarlo unos 3 cm aprox, despues solo se calibra). La finalidad de esto es de manera manual regresar el carro, se apaga y se vuelve a encender y listo. funciona nuevamente. Este error me aparece despues de haber utilizado el ADF, el cual el carro se mueve al lado izquierdo para poder escanear automaticamente los documentos. posteriormente no puede regresar. Aqui pues es donde le podemos ayudar a regresar a su posicion original. Espero que les ayude en algo.
Paper is hot
Nothing unusual about paper being hot. The fuser is a heating element of sorts and if you are printing many copies you will notice the paper is hot.
How to Reset HP Laserjet M1522nf security password
Hi the easiest way is a nv ram
1. Turn the printer off
2. Hold down the down arrow and the cancel button
3. Reboot the printer while holding the buttons and hold until permanent storage is displayed. Let go of the buttons and wait for the ready message on the display.
This reset will clear all of your saved settings and contacts, if networked print
out a configuration report after resetting the printer to view the ip
address (IPV4). If the IP address has changed you will need to update
the print driver's port tab and update the port.
Good Luck
Al,
[email protected]
HP laserjet m1522nf- I can't install software on
Do other devices work in the USB ports on the desktop? Do you use the same cable when you connect to the desktop and when you connect to the laptop or does the laptop connect to the printer via the network?
First try a different USB cable, unless other known working devices do not work. Try a different USB port. If you use a hub, try a direct connection.
I suspect you may be dealing with a port issue. Try going to the Device manager from the Control Panel and checking the status on the USB drivers. If you see a triangle with a yellow exclamation point or red x, try updating the drivers (right click on the driver). Then reboot the computer and check if this helps. Next try uninstalling the drivers and rebooting. Windows should reinstall the drivers.
Check your BIOS settings (depending on the computer press F1, F2, Esc, F10 repeatedly after turning on the computer - this may take a few tries) and make sure the ports are active. Also check in the screen saver advanced settings for a USB power saving setting.
You can try resetting the computer - unplug the accessories from the computer and remove the power cord from both the computer and the wall outlet. Press and hold the power button for 30 seconds. If you are willing to open your computer, try changing the CMOS battery (wait a minute after removing the old battery before inserting the new one). This battery is usually a lithium button battery (CR2032 is common).
I hope this helps.
Cindy Wells
Not initalizing
Formatter(main logic board) faulty,replace it.
Part no : CC396-60001
It gives a bang sound when powered on with the cartridge and no sound withour the cartridge
if this is a new cartridge, make sure all tape and other shipping devices are removed. if it is a catridge that has worked before, check to see if maybe something has broken on it. with gloves on and newspapers spread over the floor or desk, check to see if anything looks damaged. watch for toner spilling out as you rotate it. If all seems fine with the cartridge, check for misplaced or broken parts where the cartridge is inserted.
My hp laserjet 1210
Memory Supply Error 10.00.00 The printer is unable to read or write to the print
cartridge e-label, or the e-label is not on the cartridge.
Basically what is happening is the printer cannot read the small chip on the toner cartridge. The chip is located on the toner cartridge as it is inserted into the printer. 1 - Make sure the toner is firmly seated into the printer. 2 - Power cycle the printer with the toner out of the printer. Install the toner back into the printer. 3 - Install another toner cartridge. 3 - Verify that the e-label connector is firmly seated in connector
Contact a local HP Authorized Service Center for further assistance.
All lights blinking on Epson CX4300
Are the lights still blinking? because that should indicate you did forget to put something back in the correct way. I would place back the old head. put a few drops of cleaning fluid in the nozzles and gave it a few pages in full colour to print on normal paper. At first nothing will appear, but after just a few pages, some nozzles will give cleaning fluid and a little later you will see colour again. Did the same with an older Canon last weekend and it only took 4 pages and not one nozzle is refusing to work.
Be aware, if you did remove the head, you have to put everything back as it was. Because the alignment of the head is very critical. Make sure nothing is in the sensors, that check the end of carriage and so on.
My hp laserjet m1522nf gives a bangging sound when powered on with the cartridge
If this is a new cartridge, make sure all the shipping protectors are removed. if it is a cartridge that has worked before, spread some old newspaper on the floor or work surface. remove the cart from the printer and check to see if any part of it looks damaged. as you rotate the cartridge, toner powder may fall out so make sure you stay over the paper. if all seems fine with the cartridge, check the inside of the printer for the same thing, damaged parts. If damage is found, replace the cartridge or get the printer repaired.
Not finding what you are looking for?