Symbol Motorola MC9090 Mobile Computer - Answered Questions & Fixed issues


That will probably only be adjusted in the actual barcode software that you are using within the mc9090 .. at the moment I am hundreds of miles away from my 9090..but if you still have not resolved this problem. Check to see what the name of the software thats actually turning on to decode the barcodes. It should have a setting...or let me know the name of the software and I'll do some research. I'm not an expert, but have fought with my 9090 for years. I've actually reached its data capabilities and have it sitting on the shelf as relic now

Symbol Motorola... | Answered on Nov 05, 2016 | 531 views


Wireless Local Area Networks (WLANs) allow mobile computers to communicate wirelessly and send captured data to a host device in real time. Before using the mobile computer on a WLAN, the facility must be set up with the required hardware to run the wireless LAN and the mobile computer must be configured. Refer to the documentation provided with the access points (APs) for instructions on setting up the hardware. To configure the mobile computer, a set of wireless applications provide the tools to configure and test the wireless radio in the mobile computer. The Wireless Application menu on the task tray provides the following wireless applications: • Wireless Status • Wireless Diagnostics • Find WLANs • Manage Profiles • Options • Enable/Disable Radio • Log On/Off Tap the Signal Strength icon to display the Wireless Applications menu

pg 1-13,
Download manual

Symbol Motorola... | Answered on Apr 07, 2015 | 858 views


enable radio not find wlan

Symbol Motorola... | Answered on Mar 10, 2017 | 604 views


HTTPS is secure but not every website has an SSL certificate and if you try to visit a site over SSL that doesn't have a certificate you'll either get a 404 or a big fat warning

Symbol Motorola... | Answered on Dec 06, 2019 | 946 views


Constance

Contact Motorola Solutions Get Support or Zebra TechnologiesSupport Downloads for assistance.

Mark
Motorola Mobility Support

Symbol Motorola... | Answered on Feb 01, 2015 | 550 views


Hi
Contact Motorola Solutions Get Support or Zebra Technologies
Support Downloads. They aren't helping on FixYa yet so it is best to reach out directly.

Mark
Motorola Mobility Support

Symbol Motorola... | Answered on Mar 10, 2017 | 164 views


Peter
Contact Motorola Solutions Get Support or Zebra Technologies
Support Downloads. They aren't helping on FixYa yet so it is best to reach out directly.

Mark
Motorola Mobility Support

Symbol Motorola... | Answered on Jan 19, 2015 | 264 views


Usually, 95% of the times, hardware error. Will need a new scan engine.

Symbol Motorola... | Answered on Jul 14, 2014 | 761 views


If it is a Windows Mobile 5 device, reload the OS in full using SD card method. If the device is Windows CE5, you can enter IPL mode by doing a coldboot, and whilst inserting the battery back in the device, press the trigger and put it in the cradle until it enters IPL. Once there, you can either use SD card with the OS Hex files or you can use USB Download from Motorola to download the files sing a cradle from your PC. It will be recognised by the PC as this method does not use Active sync.

Symbol Motorola... | Answered on May 03, 2015 | 1,647 views


https://motorola-global-portal.custhelp.com

Symbol Motorola... | Answered on Jun 23, 2014 | 94 views


You have a virus.....download and run " USB SHOW" program
Try free downloading at cnet downloading or download.com
When you download the program scan your memory and delete all the unknowed files with del+shift keys twice

Symbol Motorola... | Answered on Jun 19, 2014 | 316 views


Hope this answers your question. First go to the .EXE file you want to be on the desktop. Touch and hold to pull open the sub-menu of that app. Select "Copy". Now go to the desktop. Find an empty section. Touch and hold down to open the sub-menu. Now select "Paste Shortcut". This will put a shortcut on the desktop for you. It will show the word "Shortcut" at the beginning of the title now, which is kind of a pain. A simple "Rename" can fix that though. That should do it!

Symbol Motorola... | Answered on Apr 17, 2014 | 389 views


If using Wavelink, you can type it by pressing SHIFT, Blue Key, N

Symbol Motorola... | Answered on Feb 25, 2014 | 4,687 views


have you been able to configure a WiFi profile using the on board utility?
If not and if you don't have the icon at the bottom right of the screen you will be able to find it in the windows folder.
If you have a profile setup, does it have a yellow ! icon on it if so, use the icon on the bottom right then> options > Regulatory in the drop down menu > and untick 'Enable...' box
If you have DHCP setup in the profile you may not be getting an IP address, you can check this in the status option from the pop up menu (bottom right).
if you are not getting an IP Address, check all your settings in your WiFi profile.
I normally start with a un-encrypted network to test the unit, then add encryption after you get it all working. You will need admin rights for the AP you are using.
Additionally i have found that some units don't like TKIP type networks with out a software update.
Hope this lot helps.

Symbol Motorola... | Answered on Nov 06, 2013 | 400 views


From the main screen, select the Wireless card >> Fusion Settings >> Wireless Status >> IP4 status.

This then shows you your mac address.

helpdesk@biastechnology.com or TEL +44(0)1202 620955

http://www.biastechnology.com/

Symbol Motorola... | Answered on Jul 24, 2012 | 13,576 views


If there is an 'X' on the radio icon not a '!' then it has been disabled.

To switch it on hit the wireless icon in the taskbar and select [enable radio].


If the radio fails to switch on then try a warm boot:-

Hold down the power button for approximately 10 seconds until the splash screen is shown.

If it still fails proceed with a cold boot:-


Partially remove the battery, hold down the On/Off button, the trigger and reinsert the battery. When the orange light on the keyboard flashes release the on/off button and the trigger.

If the on/off button or trigger is held down longer than required this occasionally causes the terminal to get caught in a warm boot cycle

If the fault is still not rectified then the device requires repair. Which we can help with as we have a specialised repair centre.


If there is an '!' on the radio icon not a 'X' then the radio cannot associate to an AP due to regulatory issues.

Hit the wireless icon in the taskbar and select [options], a pop up is then display, select [Regulatory] from the pull down menu. Then select your country and switch of 802.11d if not required. Save and exit


If you need any more help then please do not hesitate to contact us:-


helpdesk@biastechnology.com or TEL +44(0)1202 620955

http://www.biastechnology.com/

Symbol Motorola... | Answered on Jul 24, 2012 | 4,194 views


Hello, Raymond.

From FixYa Support:

To be certain that you set the static address correctly, the IP is set within the wireless profile.

On the radio icon in the task bar, select Wireless Profiles. This box then holds all your wireless profiles, including the default Motorola "out of box". Hold down the stylus on the screen and select "Add New" follow the prompts. When you get to IP Address from the pull down menu select static and then next this will take you to another screen where you can add your details.

Now you want to make them persist through either a cold boot or when the terminal has been left without a battery for a substantial amount of time.

This can be done 2 ways. When the profile has been set up highlight it by holding down the stylus on it and from the menu select export. This saves the registry key to the Application folder; a folder which persist through a cold boot. When it does cold boot it takes all the registry keys from the Application folder and builds 1 complete key.

The other way is to close the WLAN profile and selection options, from the pull down menu select export and save all profiles.

Hope this helps.

Symbol Motorola... | Answered on Aug 22, 2011 | 6,291 views


Hi Jim,

I remember having the exact same problem when I first used the MC9090. It works on such other devices like the Datalogic Viper, but not the MC9090.

The IP is set within the wireless profile.

On the radio icon in the task bar select Wireless Profiles. This box then holds all your wireless profiles, including the default Motorola "out of box". Hold down the stylus on the screen and select "Add New" follow the prompts. When you get to IP Address from the pull down menu select static and then next this will take you to another screen where you can add your details.

Now you want to make them persist through either a cold boot or when the terminal has been left without a battery for a substantial amount of time.

This can be done 2 ways. When the profile has been set up highlight it by holding down the stylus on it and from the menu select export. This saves the registry key to the Application folder; a folder which persist through a cold boot. When it does cold boot it takes all the registry keys from the Application folder and builds 1 complete key.

The other way is to close the WLAN profile and selection options, from the pull down menu select export and save all profiles.

Hope this helps.

If you need any more help then please do not hesitate to contact us:-

http://www.biastechnology.com/


or TEL 01202 620955

Symbol Motorola... | Answered on Jan 15, 2010 | 1,057 views


check in your router MAC security
if in your router MAC security is enabled then only those can connect whose MAC addresses are in allow list in router.

you can access your router with following link

http://192.168.1.1
or
http://192.168.1.0

for belkin router
http://192.168.2.1

type user name as "admin" and password as "admin" or blank or "password

then go to wireless advanced security then check MAC security if enabled then add your moto MAC in allow list.
Let me know .

Symbol Motorola... | Answered on Jul 29, 2009 | 11,997 views

Not finding what you are looking for?
Symbol Motorola MC9090 Mobile Computer Logo

45 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Symbol Computers & Internet Experts

Ekse

Level 3 Expert

13434 Answers

Vish Iyer
Vish Iyer

Level 2 Expert

75 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Are you a Symbol Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...