20 Most Recent Peavey Pv 2600 Power Amplifier - Page 7 Questions & Answers

It is possible that you have issues with caps in the power supply...I would check those first...and you can get the schematics from Peavey....

Contact Peavey...They have no problem in releasing technical documentation....I always get info from Peavey...

Hi Elijah, check that you have assigned the channels to a SubMaster to the Master and that they are not in MUTE Hola Elijah, controla que tengas asignado los canales a un SubMaster al Master y que no se encuentren en MUTE https://peavey.com/products/index.cfm/item/666/118299

There are a lot of possible problem areas it could be. I would first check that the speaker is working correctly. If so, I'd clean all jacks and pots. If that doesn't do it, it'll be time to take it to the shop.

I would think you can if the amp is rated for 4 ohms but the 4 ohm might be loader then the 8 ohm because it will get more power.

Hello John, the fuse is in the power input of Tu Peavey If you notice, on the rear panel, where the power cord is plugged in, up on the same connector, you will see a horizontal cover that can be removed by placing a tip on the underside of this cover and pulling outwards, it will come out a plastic element, which holds the fuse, this element has an intermediate space where another spare fuse can be housed I hope my comment has been useful and you can take out the fuse Keep in mind that if you blow the fuse, because I pass, check the cables and speaker connectors, that do not have any short circuit Greetings Franco Dosil Hola John, el fusible se encuentra en la entrada de energ?a de Tu Peavey Si te fijas, en el panel trasero, donde va enchufado el cable de corriente, arriba en el mismo conector, vas a ver una tapa horizontal que se puede sacar poniendo una punta del lado de abajo de esta tapa y haciendo fuerza hacia afuera, saldr? un elemento pl?stico, que sostiene al fusible, este elemento tiene un espacio intermedio donde se puede alojar otro fusible de repuesto Espero que te haya servido mi comentario y puedas sacar el fusible Ten en cuenta que si se quemo el fusible, porque paso,revisa los cables y los conectores de parlante, que no tengan ning?n cortocircuito Saludos Franco Dosil https://www.google.com/url?sa=i&source=images&cd=&ved=2ahUKEwiUpJWv4bDiAhUTIrkGHXfyDoQQjRx6BAgBEAU&url=https%3A%2F%2Fwww.tme.eu%2Fhtml%2FES%2Fconectores-machos-iec-con-proteccion-de-fusible-para-panel-schurter%2Framka_3250_ES_pelny.html&psig=AOvVaw3u39E87rodMysi11CwjaR6&ust=1558670267837577

https://amprepairparts.com/peaveyschem.htm

ya clipping it?????

1 3k amp powers up but no sound Peavey Forum Tube Amp Troubleshooting 101 Amp turns on no sound tubes wont light up Peavey 6505 Amp turns on no sound power tubes don light

You could try Googleing it, if you havn't already. Another method I've used on other guitars was to carfully remove the neck from the rest of the guitar. Manufacturers often put the production year on a tag or even printed directly on the wood body under the interfacing part of the neck. Some risk= "what if I damage my guitar?"

Probably 1997

you could have blown a resistor or transistor since it's not a tube amp.

go to: www.shematicsunlimited.com/p/peavey/ download service manual.

Hi! Contact Peavey Support peavey com Peavey com

Not sure about the KB-1, but many newer Peavey amps ( A Vyper for example) have the fuse soldered to the circuit board. If you're going to go through the effort of soldering, I'd suggest buying, and soldering in, a rear panel accessible fuse holder, so you only need to do it once.

Turn your guitar away from the amp's speakers. The pickups on the guitar are feeding the amp's signal back into the amp creating a feedback loop, especially with the gain button on. Loud volumes cause this looping path between the amp speakers and guitar pickups. You may need to reduce amp volume also.

What kind of casters are you installing? There are two types, ones that have a shaft sticking up from the base and ones that only have the flat base with four screw holes - I recommend using the flat base ones. There is no real easy way to open up the bottom of the cabinet as it is glued and then covered with the tolex or similar material. If you have the ones with a shaft I recommend getting the other type. The shaft has a socket you have to install in the bottom which makes them removable. There is no reason to remove the casters so get the ones that are screw mounted.

Yes..these amps due have fuses. Check to make sure the fuse is good, it should be close to the power cord in the back under a small, black, screw on type knob. You should also check the power on/of switch and power cord for issues.

First - Check the connections on the speaker itself - when speakers don't work. it's usually the wires from the power amp section to the speaker. If those are OK, try replacing or bypassing the headphone jack - you may have a short in the output jack. Good Luck

Sounds like your speakers may be out of phase. Reverse the connection on ONE speaker (swap the wires connected to one speaker.