20 Most Recent Coleman Powermate Premium Plus 6250W Portable Generator - Page 2 Questions & Answers

There is fault in the fuel settings, you might need to remove and clean the carburator, clean the air filter and also check if the oil is clogged.Also remove the plug and check for dirt electrode tips, if so the spark plug must be replaced. Set with the correct gap , test for the spark before it is replaced.Also check if there is impurities on the fuel. The carburator resetting must be done with care and take help if needed.

I need more info. Describe exactly the sequence of what you do tomake which circiut breakers blow ... the ones on the generator orelsewhere? Do you have a load connected to the gen? If so, what is the load?

Same. I have one to repair, Most of the wiring for the ignition system is missing, andI cannot find a wiring diagram or workshop manual ANYWHERE.

No gauges can set the governor . The governor controls the engine at a set speed, as the load on the generator varies so does the engine speed ,the governor tries to keep the engine speed constant.

If you send me your email address I will be happy to send you a diaphragm with OEM part numbers. [email protected]

1) You'd have to figure out a way to support the engine end of the rotor. Right now the engine rear main bearing is the front bearing of the generator.

2) You'd need to make a wind turbine that produces 6+ horsepower (at least) to get the 5 Kw out of it.

Usually small wind turbines drive polyphase generators that charge batteries used to run inverters. Go see: http://www.otherpower.com/otherpower_wind.html for a pretty good discussion of the problems to solve.

10W30 OIL WILL BE FINE

. Hello jflash...There are several ways to solve this problem. Perhaps the easiest is to go to an appliance store and purchase a power cord with a 4 prong 220v plug. if you go to a large RV sales site they may have an adapter for this purpose. Otherwise back to rewiring that waterpump:

3-Prong or 4-Prong ? The Difference:

3-prong color code:

BLACK (HOT ? 110-120VAC) ? May also be referred to as L1
RED (HOT ? 110-120VAC) ? May also be referred to as L2
WHITE (NEUTRAL ? 0VAC) ? Usually grounded to the equipment frame via a jumper wire or metal strap.

4-prong color code:

BLACK (HOT ? 110-120VAC) ? May also be referred to as L1
RED (HOT ? 110-120VAC) ? May also be referred to as L2
WHITE (NEUTRAL ? 0VAC) ? DO NOT ground to equipment frame.
GREEN (GROUND) ? Attach to equipment frame.

Which One to Use: According to the National Electrical Code (NEC), Article 250, installations after the year 2000, require the use of a 4-prong plug which incorporates a separate ground and neutral wire. If you currently have a home that uses the 3-prong receptacle and cord, you can continue to use it. You will have to upgrade to a 4-prong configuration, however, if you plan on relocating your current receptacle, or if the internal wires of the receptacle become damaged in any way and require repair.

Converting from 3-prong to 4-prong: Make sure you UNPLUG the appliance prior to any repairs. CAUTION: Voltages dangerous to life are still present even with the appliance turned off and still plugged in. Notably in the area of the terminal block where the power cords are installed. You will need to remove the old cord by following these steps:

1. With the appliance UNPLUGGED, remove the access panel on the back of the unit where the power cord enters.
2. With the cover removed, you will see a terminal block where the power cord is attached. The terminal wires will be colored with the WHITE wire in the middle, and the BLACK and RED wires on either end. NOTE: There should be a green jumper wire or metal bonding strap attached to the NEUTRAL (white) terminal wire.
3. Remove the terminal lugs holding the old power cord wires in place. CAUTION: Use care not to drop any nuts or screws inside the appliance.
4. Remove the bonding strap or ground wire from the Neutral terminal lug. NOTE: If disconnecting a ground wire, make sure you re-attach it to the appliance frame.
5. Loosen the screws on the strain relief connector that holds the power cord in place and remove old power cord. NOTE: If your appliance does not have a strain relief that clamps down and hold the power cord in place, it is highly recommended that you install one. This prevents chaffing of the power cord against the appliance casing, and prevents the terminal wires from being pulled and broken loose. This could pose a potential shock hazard or cause damage to the appliance.
6. Install new power cord by threading it through the strain relief connector and tighten down the screws.
7. Connect the new power cord to the corresponding colors at the terminal block (Black goes to Black, Red goes to Red, White goes to White). The difference is going to be a Green (ground) wire that will connect to the appliance frame. There?s usually a green grounding screw for this. NOTE: If you disconnected a green grounding strap in Step 4., you can connect these two wires at the same point.
8. Re-install access cover. Turn off the service breaker to the appliance PRIOR to plugging it back in. With the breaker in the off position, plug the appliance in, and THEN turn the breaker on. In the event, something was wired incorrectly, it is far better to have your hands away from the receptacle and controlled from a distance. Safety first.

These steps will work for nearly all appliances that require a 220-240VAC power cord conversion. The power cords are usually rated at 250VAC, 30 amps, and are carried by any hardware store or appliance parts retailer.

ADDITIONAL NOTES:

1. If you desire to convert an appliance from a 4-prong to a 3-prong, make sure you reconnect the bonding strap and/or ground wire to the Neutral (white) wire at the terminal block.
2. On some newer appliances, it is REQUIRED that you use a 4-prong plug in order for the timer or clock circuits to function properly due to the way they are configured. Refer to your owner?s manual for the correct recommendation. Even if you currently have a 3-prong receptacle, you still may be required to upgrade to a 4-prong if you encounter this situation.
3. In many circumstances, new appliances are NOT sold with the power cord due to the various power configurations in homes. Always refer to the contents description on the shipping container the appliance comes with to see what additional items or tools may be required for installation.

I hope this information is found to be helpful. Joe
Thanks for choosing Fixya!

If it is B&S he spring is to hold up the plastic float housing to keep a tight seal to base of carb. Sits in the center of the bottom of the plastic piece and the bottom of the bowl.

Cleaned the carb again and set idle stop screw up

Hi, When you run a small engine it will need a thinner oil. Especially if you run it in a colder climate. Here are the basic rules when it comes to oil:

• If you just bought a new mower or other piece of equipment, add oil before you start the engine. These products are shipped without oil. Even if the product is delivered to your home fully assembled, check to be sure the engine contains the right amount of oil.
• Check the oil in your mower, pressure washer, portable generator or other outdoor power equipment each time you use it. Do this when the engine is cool. If the equipment has a dip stick, pull it out and wipe it off, then reinsert it all the way and pull it out again to check the oil level.
• You should change the engine oil in your outdoor power equipment after 25 hours of use. If you are working under dusty, hot conditions, change the oil more frequently.
• Don't overfill the crankcase when adding oil. Too much oil can damage the engine.
• Briggs & Stratton offers oil specially formulated for your mower and other equipment. Our 100% synthetic oil is an all-season oil blended for all small engines. Briggs & Stratton Lawn Mower Oil is formulated for 4-cycle air-cooled engines, and 2-Cycle Ashless Oil is a premium ashless oil with gas stabilizer made for use in 2-cycle air-cooled engines.

Your battery charge rectifier is not working. Measure the input voltage going into the rectifier. Should be around 30Vac. If voltage is present then you rectifier is bad.

See some of my responses to other peoples generator problems. If you have no or very little electrical output, then you have overloaded the generator by placing a demand for too many amps from too many appliances for the size of the generator. You will have blown a capacitor, resistor, or similar item. Someone with a good electrical background will need to diagnose the problem and find the blown part.

I think you did not set the AIR GAP when you replaced the coil. Most are set .010 . Look on you tube it will how how to set it.

The ones on the left and right are the lines ( 120 volts ) the top one is the neutral and the botton with the small L is the ground.

http://www.powermate.com/contact.php

Buy an adapter.