Remington Electric Chain Saw - Answered Questions & Fixed issues

Remington Pole Saw Carbon Brushes If you're Remington Pole Saw is slowing down, throwing sparks, or not starting you may need to replace the carbon brushes. Replacing brushes and cleaning commutator early can prevent damage to motor armature! Remington carbon brushes on E-bay Search for: Remington Pole Saw 8 AMP Carbon Brush

No, the largest electric pole chain saw that can be attached to a pole with the Remington Pole Saw kit, is a 10" saw.

You can go to Master Distributors to find out more detailed info about your situation and speak with one of their reps.

http://www.remingtonchainsaw.com/

Hope you found this very helpful, best regards!

All I can say is bypass the wiring inside the pole.

well if its an electric powered model as the title says it is , then the only oil it should have is Bar/chain oil there should be a little cap just forward to left of the trigger this should be kept full of bar/chain oil for its use

There is a very in depth explanation in this Remington OM.
http://shoppingcart.msservicecompany.com/msservice_net/product_files/113005-01D/113005-01D_OM.pdf

If you have more questions or need additional help please reply below and I will get back to you. Good Luck. HTH
Lou
Thank You for using FixYa.

Remove the cover, loosen the bolts to allow the bar to slide toward the sprocket. Lift chain off the sprocket and pull out from the notch in the bar. Be sure to turn the chain the same direction, otherwise you will be cutting with the back side of the blades. Slide the new chain blade onto the sprocket then fit into the bar. Once that is accomplished pull the bar firmly outward watching to see that the blade stays inside the slot of the bar. While keeping pressure on the chain and bar, tighten the retaining bolts and replace cover

Remington Pole Saw Carbon Brushes If you're Remington Pole Saw is slowing down, throwing sparks, or not starting you may need to replace the carbon brushes. Replacing brushes and cleaning commutator early can prevent damage to motor armature! Remington carbon brushes on E-bay Search for: Remington Pole Saw 8 AMP Carbon Brush

Remington Pole Saw Carbon Brushes If you're Remington Pole Saw is slowing down, throwing sparks, overheating or not starting you may need to replace the carbon brushes. Replacing brushes and cleaning commutator early can prevent damage to motor armature! Remington carbon brushes on E-bay Search for: Remington Pole Saw 8 AMP Carbon Brush

They used to be owned by DESA industries. But I beleive that may have changed

How can I get the serial of a Magtech 7022 .22 rifle purchased in 1999.

Take your chainsaw to a saw shop that repairs chainsaws. They should be able to make one for you or look one up and order it for you. I have found shops in the yellow pages looking under saws.

My best advice is to find a lawn and garden shop that services chain saws. Take the chain you have and they can make one just like it.

not sure about this particular model but many saws have the brush accessible from the motor casing. Look for a round disc with a screwdriver slot on the motor casing. These round discs should be on opposite sides of the motor housing

Chainsaws use a non fling oil to lubricate the cutting chain, the oil will be clearly marked non fling chain oil, if you want to be enviromently friendly use a bio chain oil.

Jo: Unplug the saw. Lay the saw on it's side so the chain and bar are up (lay it on 4X4 blocks or something similar so the motor housing doesn't make the saw rock back and forth) Loosen the two 1/2 or 9/16 nuts... don't take them off, just loosen them a turn or two. Look toward the saw where the bar comes out (the front of the housing where the blade comes out). You will see a small screw head. Turn the screw clockwise (as if you were tightening it) As you turn that screw, the chain will tighten. Put on some gloves and pull the chain around the bar (as if the saw was running, but you are the motor). The chain should move with a little resistance. Pinch the chain at the top-middle of the bar and pull the chain up away from the bar. the chain should pull away from the bar no more than 1/16 to 1/8 inch. If you look carefully between the bar and the chain, you'll see the dogs that run in the groove in the outside circumference of the bar. None of the dogs should be fully exposed when you pull up on the chain (in other words, None of the dogs should come completely out of the bar's chain groove when you pull up on the chain. Now, tighten the two nuts on the back of the bar. Snug them down good... if the bar slips on those two nuts, the chain will come off while you are cutting. Good luck

Use chain saw chain oil or 30wt non detergent oil.

Click here to see parts.

This should be part # 107713-01 - internal gear. Most likely used with a panhead shoulder screw part # 076905. Source: PartsFor.com

Probably the shaft on the sprocket has sheared off.Knox Knolls Outdoor Power EquipmentSpringfield, IL 62704www.knoxknollsope.com

Jim it is so long out of production about the only thing available is the OM. If you can get a pn off the original switch Allied or Newark is an option. Maybe a trigger switch from a saw in current production can be modified to fit.
Different model Poulan electric saws follow:
1. http://www.ordertree.com/modelinfo/PWE/1220-Electric-Saw/75.1220-Electric-Saw.1.59.1.html
2. http://www.ordertree.com/modelinfo/PWE/1420-Electric-Saw-Type-2/75.1420-Electric-Saw-Type-2.1.59.1.html
3. http://www.ordertree.com/modelinfo/PWE/1625-Electric-Saw-Type-2/75.1625-Electric-Saw-Type-2.1.59.1.html
“EL-14“ through “ES400” here (5±):
Poulan.com
http://www.ordertree.com/modelinfo/POULAN-WEED-EATER/75.59.html

A length of spring steel and almost any micro switch might also be an option. Beyond that I am out of ideas.

If you have more questions or need additional help please reply below and I will get back to you. Good Luck. HTH
Lou
Thank You for using FixYa.