20 Most Recent
Grizzly H7670 Mini Hvlp Spray Gun, Stainless Steel Cup - Page 3 Questions & Answers
Emglo AM78 4CHV oil capacity
I just rebuilt my Emglo AM78 4CHV, new pressure switch, unloaded, check valve, aftercooler, and changed the #30 oil, It takes 4oz.
Runs like new after not cutting in/out correctly and purging air before reaching 125 psi. Kicked it down to 115 max psi via main spring setting. Don't need 125 for trim nailing and siding.
FYI don't use cheaper generic 125 psi pressure switch from Amazon!!
use Jenny M4-1247 (140-1074-01)
How to fix High sump pressure fault on IR 75i compressor
It sounds like the pressure rises too high.
Did you set the pressure correctly? Does it unload at the right pressure?
If not, there's a problem with the load/unload system and the inlet valve stays open
call IR for more help
Bump trigger lever not making contact with firing pin
Hey! I think this brief info I am offering below can assist.
To properly install the trigger on your Paslode 501089 Urethane Retainer, follow these steps:
- Ensure that the tool is disconnected from the power source and the fuel cell is removed for safety.
- Remove any existing trigger components from the tool, including the old trigger and its associated parts.
- Take the new Paslode 501089 Urethane Retainer and insert it onto the trigger pin, ensuring that it fits securely and snugly.
- Align the bump trigger lever with the trigger pin and make sure it engages properly. It should make contact with the pin that fires the gun.
- Double-check that all components are properly aligned and seated. Ensure that there are no obstructions or misalignments that may prevent the trigger from functioning correctly.
- Reassemble the remaining components of the tool, such as the housing and any screws or fasteners that were removed during the disassembly process.
- Test the trigger by connecting the tool to a power source and performing a dry fire test without nails or fasteners. Ensure that the trigger functions smoothly and consistently.
If you are still experiencing issues or have further questions about the installation process, it is recommended to consult the user manual for your specific Paslode model. The manual should provide detailed instructions and diagrams on how to install and troubleshoot the trigger assembly. Additionally, you can contact Paslode customer support or reach out to a professional service center for assistance.
Atlas copco compressor (ZR VSD FF 90)displays "main motor converter alarm" after a shutdown. It refuses to be reset. How can this be resolved?
The "Main Motor Converter Alarm" on an Atlas Copco compressor (ZR VSD FF 90) typically indicates a problem with the main motor converter. Here are a few steps you can take to try resolving the issue:
- Power cycle the compressor: Turn off the power to the compressor and let it sit idle for a few minutes. Then, turn the power back on and see if the alarm clears. Sometimes, a simple power cycle can reset the system and resolve temporary faults.
- Check for loose connections: Inspect all electrical connections, including those related to the main motor converter. Ensure that all connections are secure and tight. Loose connections can cause issues with the motor converter and trigger alarms.
- Verify power supply: Ensure that the compressor is receiving the proper power supply within the specified voltage and frequency range. Voltage fluctuations or incorrect power supply can cause issues with the motor converter. Consult the manufacturer's documentation or contact Atlas Copco support for the correct power requirements.
- Consult the manual or contact support: Refer to the user manual or contact Atlas Copco technical support for specific troubleshooting steps and guidance related to the "Main Motor Converter Alarm." They may provide you with further instructions or recommend specific actions to resolve the issue.
- Professional assistance: If the alarm persists despite your attempts to resolve it, it is recommended to seek assistance from an authorized service technician or Atlas Copco service center. They will have the expertise and necessary tools to diagnose and repair the motor converter or any related issues.
Fix a trigger on husky 2190 hfc framing nailer 3 1/2 21 degree user manuals
If you are experiencing issues with the trigger on your Husky 2190 HFC framing nailer and don't have the user manual, here are some general steps you can take to troubleshoot and potentially fix the problem:
1. Safety Precautions: Before attempting any repairs, ensure that the nailer is disconnected from the power source and there are no nails in the magazine.
2. Visual Inspection: Inspect the trigger mechanism for any visible damage, debris, or misalignment. Look for any loose or broken parts that may be affecting the trigger's operation.
3. Lubrication: Apply a small amount of lubricating oil specifically designed for nail guns to the trigger mechanism. This can help ensure smooth movement and proper functioning of the trigger.
4. Check Spring Tension: The trigger mechanism relies on springs for proper operation. Check if the springs are intact and properly tensioned. If a spring is damaged or too loose, it may affect the trigger's performance.
5. Adjust Trigger Depth: Some nailers have a depth adjustment feature that allows you to control how far the nail is driven into the material. Ensure that the trigger depth setting is properly adjusted to the desired level.
6. Test the Trigger: Reassemble the trigger mechanism if you had to disassemble it for inspection. Test the trigger to see if it operates smoothly and consistently. Check if it engages and releases properly.
7. Seek Professional Assistance: If the trigger still doesn't function correctly after attempting these steps, it is recommended to seek assistance from a professional tool repair technician or contact Husky customer support for guidance. They will have the expertise and access to specific parts and information to help you resolve the issue.
It's important to note that working on power tools can be dangerous if you are not familiar with the proper procedures. If you are unsure or uncomfortable with any step, it is best to seek professional help.
Where to find airy nailers parts
ask maker for the parts list
pick a part and ask them for it.
same answer for any machine or tool.
ask them.
we sell no parts here.
Not finding what you are looking for?