20 Most Recent
Grizzly H7670 Mini Hvlp Spray Gun, Stainless Steel Cup - Page 5 Questions & Answers
How do I reset the service light on my
To reset the service light on your Ingersoll-Rand TS6A air dryer, you will need to follow these steps:
- Turn off the power to the air dryer.
- Press and hold the "On/Off" and "Reset" buttons simultaneously for at least five seconds.
- Release the buttons and turn the power back on to the air dryer.
If the service light does not reset, you may need to refer to the manufacturer's instructions or a repair manual for further troubleshooting. It's also important to note that resetting the service light does not address any underlying issues that may have caused it to turn on in the first place. You should have the air dryer checked and serviced by a qualified technician as soon as possible to ensure that it is operating correctly.
Nail gun, stappler wont fire
Hi,
Please attempt to push out some test staples at different angles with your mastercraft. That is, I'd like you to rotate 90 degrees 4 times and attempt to push a staple each time. If it works only at certain angles, then we know that something has come apart within the mastercraft. And you've already applied oil on the mastercraft which is good. If possible, please swap out the staples and attempt to sho ot with the new set. Otherwise, I think Home Depot or Lowe's should be the next stop so they can examine the device and determine how to troubleshoot.
Thank you.
Bostitch SX1838K 18GA Narrow Crown Finish Brad Nailer and Stapler. I bought a lightly used SX1838. Tested it a few months ago. Took me a minute to get it to fire but it seemed to be fine.
If your SX1838 is not firing when you try to use it on your carpet project, there may be a few possible issues that you can try to address. Here are some steps you can take to troubleshoot the problem:
- Check the power source. Make sure that the power cord is securely plugged into the SX1838 and into a working outlet. If the power cord is damaged or not properly connected, the tool may not be receiving enough power to operate.
- Check the switch. The SX1838 has a switch that allows you to select between two modes of operation. Make sure that the switch is set to the correct mode for your project.
- Check the trigger. The SX1838 is triggered by pressing the trigger on the handle. Make sure that the trigger is fully depressed and that it is not obstructed by any debris or other materials.
- Check the nozzle. The SX1838 has a nozzle that sprays the adhesive. Make sure that the nozzle is clear and not clogged with any debris or adhesive.
If you are still unable to get the SX1838 to fire after trying these steps, you may need to contact the manufacturer for additional troubleshooting assistance or to have the tool serviced.
How do I take the pin out of saftey neutral switch 2004 monte carlo ls
To remove the pin from the safety neutral switch on a 2004 Monte Carlo LS, you will need to locate the switch and locate the pin. The safety neutral switch is typically located on or near the transmission, and it may be necessary to consult your vehicle's owner's manual to find its exact location. Once you have located the switch, you should be able to see the pin that holds it in place. To remove the pin, you will need to use a tool such as a small flathead screwdriver or a nail to push it out. Gently push the tool against the pin until it pops out of the switch. Be careful not to damage the switch or any other nearby components while removing the pin.
O-ring size for bostitch sb-1850bn trigger unit
Hi,
if this data is not in any of the documents that came with the nailer kit product, please work with one of Bostitch vendor partners for the product in order to acquire the ring size information. Some of these vendor partners would be Lowe's and Walmart. You can call ahead before attempting to visit each partner.
Thank you.
How to check and maintain oil for CP 0200608 coleman powermate 6 gallon
on the compressor end is a plug that when removed is is oil level dipstick. you will need to ad 30 weigh non detergent oil until level is correct by measuring with dip stick. do not overfill, if you do you will need to empty by tipping compressor of on it side.. where did smoke come from . did it smell like oil burning or electrical.
Not finding what you are looking for?