20 Most Recent Hitachi H60MRV Sds Max Demo Hammer - Page 2 Questions & Answers


3 to 4 ounces for first fill. You actually unscrew the oil gauge with the little wrench that should have come with the tool and add the oil there. After putting the cap back on, hold the tool upright to check the oil level. Check daily and add oil when the level drops to 1/4 when checking as described above.

Hammering | Answered on Apr 05, 2019


kango 950 was the hammer drill version. Usually when they stopped hammering they were due for a rebuild. These units have a aluminum piston that rides in a steel tube striker. When the 2 rubber piston rings wear out you will get the described problem. The Kango's use a special tan grease so you cannot just yank it apart and replace the 2 rings with o-rings and grease. I had to rebuild 15 900 and 950's because the previous mechanic used the wrong grease. https://project21designs.com/kango-950-parts
The link sells grease & rings.

Hammering | Answered on Mar 13, 2019


You need to check armature gear it can be damaged. Connection rod can be broken or you just need new o-rings and grease

Hammering | Answered on Feb 09, 2019


Buy a new switch the old switch was modificated by an maintenance kit if you have an old blue or red real Kango from England. or black Atlas Copco .
But if you have the red Milwaukee Kango then there is only a new switch to replace.

Hammering | Answered on Aug 28, 2018


  1. The total condition of the seal anvil piston and striker are very important for the total condition of impact when spending a service kit (maintenance) when there is leakage at the front part everything will be hot inside and the rings will harden again quickly.


kango 900 950 round switch housing

Hammering | Answered on Aug 16, 2018


There is no question here

Hammering | Answered on Aug 03, 2018


Spay it with WD40 penetration fluid.

Hammering | Answered on Jul 24, 2018


Contact Arksen directly with your request.

Hammering | Answered on Jun 26, 2018


BLACK+DECKER drill quickly replaced my cordless drill for all of the heavy duty tasks, and it continues to be a great "work horse". More details about the drill Best Hammer Drill

black-decker-dr670-hammer-drill-vqugf4lgsewrsyjnp2d3onew-4-0.jpg

Hammering | Answered on Jun 04, 2018


will it run with the fuel cap off if yes there is a vacuum in the fuel tank
caused by a blocked breather
if it will not run with fuel cap off the float valve could be blocked

Hammering | Answered on Apr 08, 2018


Could be a stuck impact bolt, try banging the chisel hard against the concrete and see if it makes a difference. If not it is probably an internal piston/cylinder fault. Take it to a repair centre. You can get a drawing from Hitachi's web site if you wish to do it yourself.

Hammering | Answered on Feb 07, 2018


One of the first things that you want to check, is the wire connections above the light that is flickering. It would be a good idea to check the first light also, and the switch connections, due to the age of the wiring. If all this fails, then you are probably right and the socket of the flickering light should be changed.
It would not hurt to go in grids and work your way thru the house, checking the wiring and tightening the wire nuts, or connectors.
Enjoy :)
Paul

Hammering | Answered on Oct 10, 2017

Not finding what you are looking for?
Hitachi H60MRV Sds Max Demo Hammer Logo

0 questions posted

Ask a Question

Usually answered in minutes!

Top Hitachi Hammering Experts

John Trevino

Level 3 Expert

1420 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

2015 Answers

ray gallant

Level 3 Expert

66184 Answers

Are you a Hitachi Hammering Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hitachi Hammering

  • Hitachi Hammering

Most Popular Question

kind oil

  • Hammering
Loading...