Top 20 Hitachi H60MRV Sds Max Demo Hammer Questions & Answers


Try just stopping and starting the machine off a while.to see if the hammer appears.

Hitachi... | 431 views | 0 helpful votes


There is a sight glass on the side for you to see the oil level. Make sure they are always checked. You can buy the oil at any service center. Hilti makes oil too and can probably be purchased at Home Depots. Also the Home Depots that have tool rental programs would most likely sell the Hitachi oil too.

Hitachi... | 998 views | 1 helpful votes


For most climates a good oil to use is air compressor oil (mineral). Sold at Lowes and many other stores. It has great lubrication properties and can take good amount of heat. In very cold climates where oil could thicken, store hammer indoors to keep warm until ready to use. Good luck

Hitachi... | 365 views | 0 helpful votes


Hitachi sells a pneumatic oil for use in its air power tools. Your local Hitachi dealer, or any pneumatic dealer will sell the oil. The brand is not as important as using a few drops directly into the air fitting when starting a day of work. If used heavily, oil it again mid way through the working day.

Hitachi... | 674 views | 0 helpful votes


HITACHI EXCAVATOR MANUAL

Hitachi... | 1,442 views | 3 helpful votes


In most brands of this breakers there is no oil used , (only if there is an oil sight glass on it) some rotary hammers or breakers with high rpm have oil lubrication ( in most case its a sinc free hydraulic oil) (or special Turmopol oil (by Hilti) but this kind of hammers have no high rpm for oil and i think its having a normal grease lubrication and its enough for replace the grease after the carbon brushes are short and the tool stopped working then its time for service o-rings and seals and grease for the next service by the ALdi service.??

Hammering | 65 views | 0 helpful votes


no information generic answer --notify the manufacturer or owners manual for assistance

Hammering | 64 views | 0 helpful votes


If an oil sight glass is in the modelrange of the brand ROK Rottela 40 , but if no sight glass is used in the model then often is to use special Grease lubrication. or only an special volume of oil and most used of them are zinc-free hydraulic based and included in the manual instructions of a maintenance set (service kit)wear parts set.

Hammering | 135 views | 0 helpful votes


kango 950 was the hammer drill version. Usually when they stopped hammering they were due for a rebuild. These units have a aluminum piston that rides in a steel tube striker. When the 2 rubber piston rings wear out you will get the described problem. The Kango's use a special tan grease so you cannot just yank it apart and replace the 2 rings with o-rings and grease. I had to rebuild 15 900 and 950's because the previous mechanic used the wrong grease. https://project21designs.com/kango-950-parts
The link sells grease & rings.

Hammering | 230 views | 0 helpful votes


3 to 4 ounces for first fill. You actually unscrew the oil gauge with the little wrench that should have come with the tool and add the oil there. After putting the cap back on, hold the tool upright to check the oil level. Check daily and add oil when the level drops to 1/4 when checking as described above.

Hammering | 125 views | 1 helpful votes


You need to check armature gear it can be damaged. Connection rod can be broken or you just need new o-rings and grease

Hammering | 133 views | 0 helpful votes


Buy a new switch the old switch was modificated by an maintenance kit if you have an old blue or red real Kango from England. or black Atlas Copco .
But if you have the red Milwaukee Kango then there is only a new switch to replace.

Hammering | 384 views | 0 helpful votes


  1. The total condition of the seal anvil piston and striker are very important for the total condition of impact when spending a service kit (maintenance) when there is leakage at the front part everything will be hot inside and the rings will harden again quickly.


kango 900 950 round switch housing

Hammering | 709 views | 0 helpful votes


Contact Arksen directly with your request.

Hammering | 596 views | 0 helpful votes


BLACK+DECKER drill quickly replaced my cordless drill for all of the heavy duty tasks, and it continues to be a great "work horse". More details about the drill Best Hammer Drill

black-decker-dr670-hammer-drill-vqugf4lgsewrsyjnp2d3onew-4-0.jpg

Hammering | 625 views | 0 helpful votes

Not finding what you are looking for?
Hitachi H60MRV Sds Max Demo Hammer Logo

0 questions posted

Ask a Question

Usually answered in minutes!

Top Hitachi Hammering Experts

John Trevino

Level 3 Expert

1420 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

2015 Answers

ray gallant

Level 3 Expert

66086 Answers

Are you a Hitachi Hammering Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hitachi Hammering

  • Hitachi Hammering

Most Popular Question

kind oil

  • Hammering
Loading...