LG WM-2277HW Front Load Washer - Page 2 - Answered Questions & Fixed issues

cheaper to check for a problem in the impeller first as the pump motor seldom fail but there are problems with items jamming the impeller

Replace the bad thermistor. Costs about $6. Not that hard to do. Check out repair videos at repairclinic.com. Or appliancepartspros.com

loose wires connection or pc board

Take tray back out. Take all the components apart and clean all the tubes. Capillary action will not work with residue left on the parts.

it is a drain hose so there is no need for a filter the water to drain will be dirty so there is no point in filtering dirty water destined too go down the drain

It is a door lock error caused by bad door lock switch or if your door is very hard to swing closed because the hinge is corroded, then the hinge could be causing the door lock to error.

Your model has a button labeled beeper. Put that on high.

Not motor. Most likely one of these: bad bearing or seal, worn shock absorbers, broken spider(drum support to spindle)

send it all back and get a new one.tell your tech that you only need the front panel that goes to your washer,if they send something else that needs more parts to work,DO NOT PAY FOR ANYTHING,IT IS A SCAM,notify your techs boss

Does spin only work well?

I would replace the thermistor. $6 part. Worth a try. Are you sure the error is not "tE" instead of "LE"?

Have you tried eBay for the parts?

Try thinning softner with water.

turn off the child lock CL

The impeller may have come off the pump motor shaft. Generally, you will notice a louder sound when the pump runs if this happened.
Unplug the machine. Remove the filter recess by removing the one screw inside and using a putty knife at the left and / or right edge and popping it out. Pull the machine out about 18 inches and tip it back, resting it against the wall. Remove two more screws behind where the recess was holding the pump housing on. Reach under the machine and remove pump. There is a tab to depress under the pump housing to release it from the base. The pump motor is held onto the housing by three screws. Remove them and inspect the impeller to see if it has come off the shaft. If it has, pushing it back on will not solve the problem, as it will come off again. Install new pump motor and reassemble. Clean washer tub with the longest, hottest cycle and three Ah-fresh tablets, Whirlaway hot tub cleaner, Smellywasher cleaner (smellywashercleaner.com) or Tide washer cleaner. Repeat. From now on, use only 1 tablespoon of HE laundry detergent per load (1/2 T if 2X concentrate) and only 1 teaspoon of fabric softener per load if you use it. (these machines use very little water, and thus require reduced amounts of additives to work properly)

is there visible water in the washer if so its not draining and wont spin until it does. Check the pump clean out for a clog. If the water is in the tub and the cleanout screen is clear listen to the pump run is it just humming like its jammed or bad? or can you hear the pump run like it should? Does the door lock? It has to or it will not spin. Is the basket free try spinning the basket by hand. Or does it look like its trying to spin but slipping the could be a bad rotor in the back they sometimes strip out as they have plastic gearing and the shaft for the basket is steel and will just break off all the tiny plastic teeth on the rotor. It back of the unit is a panel 2 to 4 scews take that off now you see a round wheel like thing with 1 nut on it remove the nut pull off the rotor and look in it you will see the gear teeth in the center hole they may be there or they may be missing.

2nd set of buttons from the right. says beeper, push it

since it is a washer-dryer, the lint trap is in line with the drain. you have to empty the drain basket. there's an access door on the bottom left, first take the little tube out and drain the remaining water, then open the large drain cap to the right and clean out the trap. once you're done put it all back together and it should work. you're supposed to do this every few months. It was too much for me to deal with so i ended up buying a separate dryer and just use the washer .

door lock is not designed as a repairable item.just buy a new one.if it still dosent work,give the door an additional push.if it still dosent go ,brobably a fault with the main power board.(rare)

i think it is a tE error code. thermistor issue. easy, cheap fix. check out appliancepartspros.com or repairclinic,com for how to videos and parts.