LG WM1814CW Front Load Washer - Page 6 - Answered Questions & Fixed issues

Hi,
Here is a tip that I wrote that gives more detail about how to fix the OE codeon LG washers....

LG Washing Machine OE Error Code
heatman101

Hi,

Problems with a washing machine not spinning or not draining are often interrelated..

If you are having a problem with your top load washer then check out thistip...

Washing Machine does not Pump or Spin


If you are having problems with your front load washing machine then checkoutthis tip...

Front Load Washing machine not draining and or not spinning


heatman101

that sounds like the filter access, should have a rubber washer/seal if thats damaged it will leak, have the seal replaced

Hello & Welcome to FixYa

Yes correct a clogged pump filter will cause this problem however, if I may I will recommend you to run one more cycle outside just make sure that the pump is running fine and it drains fine, after that you can place the washer inside and it will work. Please get back to me if you have any other questions.

Kevin

Hi.

If the model is WM1814CW, then the drain filter is located behind the small door located at the left hand corner at the bottom of the appliance's front side.

Regards.

Ginko

Hi

One of the most common problems with washing machines, however, is that they won't spin. Usually this is caused by an issue that easily can be fixed, but other times it can be more serious. In some cases, just the balance of the load can cause the machine not to spin. For that reposition the clothes. Close the lid and retry. The washer may not spin at all if the tub is unbalanced. Check the lid switch for wear. Replace a worn lid switch by first using a screwdriver to remove the top of the machine. Remove the cabinet holding the old switch in place by unscrewing the two console screws, tilting the console back, removing cabinet clips, and unlocking the lid switch block. Unscrew the mounting screws, and disconnect the ground wires before removing the old switch. Insert the new switch in its place. Then check for lose or worn or crack in belt. If these signs appear, remove the old belt by tipping the washing machine over on its side, and unscrew the clamps securing the pump coupling with a screwdriver. Place the new belt over the transmission pulley, and then over the motor pulley's nearest edge, slowly turning the motor pulley to pull the belt around and into the pulley. Replace the washer's motor by firmly grasping on the metal slip-on connectors holding the wires in place, allowing you to pull the connectors apart. Use a screwdriver to unscrew all of the screws holding the motor in place, and remove the old motor. Insert the new motor in its place. Secure the new motor to the machine with screws, and reconnect the motor's wiring harness.

Replace the washer's pump by removing the service panel on the back of the machine with a screwdriver and disconnecting the washing machine drain line and the rubber pump outlet hose. Remove the fasteners holding the pump to the bottom of the machine, along with the drive belt from the pulley below the pump. Replace the old pump with a new one, and reinstall the drive belt back on the pulley, reinsert the fasteners and reconnect the rubber pump inlet and discharge lines.

So there are various conditions when a washing machine wont spin. Please check this link to get a detailed idea related to your problem:-

http://www.repairclinic.com/Washing-Machine-Troubleshooting?red=Washing-Machine-Repair-Help#itdoesntspin

Please get back to us if you have further query else please accept the suggestion. Thank you for contacting fixya.com

Hello there and thank you for choosing fixya
An IE error code will appear if the washer has not filled with water in approximately 8 minutes. If an IE error code appears on the washer, check to make sure both hot and cold-water taps are open completely. After both valves have been opened, unplug the washer for 10 seconds and retry the wash cycle.
There are filters on the inlet hose connections of the washing machine. They are intended to filter away mineral deposits from hard water and other debris from getting into the unit. If clogged, water will not flow through these filters into the washer. Turn off both the hot and cold water taps, disconnect the inlet hoses from the back of the washing machine, and clean the inlet filters gently but thoroughly.
If the inlet hoses are not attached to the machine correctly, it will prevent proper water flow to the washer. Turn off the hot and cold water supply then disconnect and reconnect the inlet hoses. Ensure that they are threaded properly. After the hoses have been reconnected, open the water taps completely, check for leaks, and unplug the washer for 10 seconds and retry the wash cycle.
And finely if all of this does not work then the inlet valve on the machine needs to be replaced ok?
Hope this all helps

Take a look at this link for more information on this error code.

Hi,
Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...

Dishwasher Problems - Waterwill not drain out

heatman101

Hi from retired Englishman in SW France,

'LE' stands for Lock Error. There is likely to be a problem with either the door solenoid/lock or the 'door closed' sensor when there is vibration/movement from the drum turning, requiring a service engineer's attention I suggest ;-0(

If this has assisted and/or clarified the situation for you please consider a 4 thumbs up on our rating.
Thanks and good luck!
John C

what u simply need to do is just dont over load the washer den also u check the belt at the back of the the washer or u call ur service provider

Here is the answer !!! My LG front loader has leaked once a year for the past 4 years. The rubber bellows (a part underneath the washer) cracks and causes the leak. DO NOT LET THEM TELL YOU THAT YOU ARE USING TOO MUCH DETERGENT ... THAT JUST AN EXCUSE !!! The part costs around $12. Here's the link ...

http://www.repairclinic.com/SmartSearch/SmartSearch.aspx?R=1514&searchText=LG%20Washer

Most likely the rear seal has failed and thus water made it into the rear drum bearings. Bad news. You can generally confirm this by removing the rear access cover to see if there is sign of water leakage from the center of the drum in back. (rusty stains on the motor or actual water drips there) If so, rear bearing replacement and a new "spider" could run over $500. If no sign of water leakage, possibly only the inner spline of the motor rotor stripped out, which is an easy and MUCH less costly repair. (rotor carries at least a 5 year part warranty too. Newer models cover it up to 10 years)

Make sure the dispenser is clean and free of debris inside the containers. You may have to take the dispenser apart and clean it out in the sink.

Pull the drawer all the way out till it stops. At the rear of the drawer, you will find a button to push down and it will unlock the drawer to remove out completely. Good luck.

You have a ball sensor that is located in the rear of machine just behind the rear panel. Check to make sure the ball sensor is properly mounted to the metal frame and the frame is not bent inward as this will make contact with the tub when it is try to spin. Good luck.

You may have a problem with the ball sensor. Look in the back of the washer. On the right side as you're looking at the rear, does the frame look slightly dented in?? If so, you will need to pound out the metal. The reason is that the ball sensor is located on the lower right side of the back panel and if it is pushed in enough, the spinning movement from the tub will knock the ball sensor causing the control board to display UE error code. Good luck

There are 2 special tools you will need to change the door gasket. Call LG and order the door spring removal tool. There are 2 of them.

Parts Diagram and parts listing can be foundhere
http://www.appliancepartspros.com/partsearch/model.aspx?model_id=5520805&diagram_id=28702794#d28702794

If the water still operates then it is the panel switch. If the washer does not operate, then it is the door switch.