20 Most Recent LG WD-1280FHD Front Load Washer - Page 8 Questions & Answers

Check that the magnet that is fitted to the lid of the washer is present or whether it has moved.

User manual https://gscs-b2c.lge.com/downloadFile?fileId=KROWM000189904.pdf says on page 28 and 30 for 0E error. It says Drain hose is kinked or clogged, drain filter is clogged. Clean and straighten the drain hose and Clean the drain filter.

The bearings are failing or devoid of lubrication.

You can't they are sealed. You just replace them. The sealed bearing units are shown here. Change them yourself and save a callout and an hour and a half labour.https://www.google.com/search?q=LG+TROMM+bearings

We need a Model # to assist you. Please.

I would suspect a clogged drain pump or sump pump. see pics

I have the same problem. please let me know if yours got fixed

Sears Parts Direct is one source of the parts diagrams, https://www.searspartsdirect.com/model/1vc37q1bdj-003204/lg-wm3987hw-washer-parts . See the Dispenser assembly parts diagram for the water inlet valve. If you can watch the entire cycle, try turning off the shut-off valves for the washer inlet hoses after the rinse cycle and before the dry cycle starts. Water should not flow into the washer/dryer with the shut-offs closed. I've seen inlet valve solenoids fail in the open position or in the closed position. I've never seen a control board that sent open messages randomly. (Sometimes, there is damage to the control board or corrosion or damaged wiring that stops the control board from sending the open/closed message to the solenoid.) I hope this helps. Cindy Wells

To load your LG washing machine, open the door of the machine, and place your laundry inside, close the door securely, and follow the machine's user manual for specific instructions on turning it on from the manual book.

check these sites... https://www.google.com/search?q=u3+error+code+lg+washer

The carbon brushes are worn out and need to be replaced. Also the armature needs replacing as well.

It could be from a load that is not balanced.Or the drain filer might be clogged and full of debris and needs to be cleaned out. Also the drain hose maybe be kinked or twisted too.

That is the problem with top loaders, central agitators and long items like towels, They get tangled and tear. It is also likely that your towels are worn out. To wash successfully, you need a lot of water and only 3 or 4 towels. Front loaders don't do that and uses a tenth of the water and energy to heat that water.

Front Load Washer with TrueBalance

https://www.lg.com > ... > Washing Machines 7 cubic feet and ultra-large at 4. 3 - you can fit more into every load - saving time and energy. Slamproof™ Lid: With a top-load LG washing machine, you' ... Matching Dryer: DLE2050W Weight: 190 lbs Capacity Facet: 4.0 Energy Star Compliant: Energy Star Rating: 4.6 · ‎351 reviews ..

Question edited for a lot more clarity. Clean it with a pot brush, or just replace it. https://www.google.com/search?q=LG+Front+Load+Washer.+The+drain+hole+in+the+rubber+gasket+is+CLOGGED ..

Question edited for clarity, 'make model (what it is)'. Question moved from LG Car Audio. Yes, that is normally the way to do it.... but

It will be fine. The transit bolts are there to protect the springs and dampers from stretching if the machine is tilted or laid on its back during shipping to the seller and delivery to the home. In use with the transit bolts removed it allow the springs, the shock absorber and the big concrete block to absorb movement as the spin evens out the balance of the clothes with the first part of the spin. It also stops the machine walking across the floor as all of the movement is transferred to to case and feet. It will be fine, I have done it myself after I moved from one house to another and then didn't do any washing for a week or two. Enjoy your new machine. Finally, just for fun

http://manuals.appliancesonline.com.au/lg-frontload-washers/lg_frontload_washers_user_guide.pdf

If the gear system of your LG direct drive washing machine is broken even after you have replaced it and checked the clutch regulate motor, there could be a few other reasons why this is happening. Here are some possible solutions to try:

1. Check the motor: If the gear system is still not working, it could be a problem with the motor. Check if the motor is functioning properly and if it is getting power.
2. Check the control board: The control board could also be a potential issue. Check if the control board is functioning properly and if any of the connections are loose or damaged.
3. Check the drum bearings: The drum bearings may be worn out, causing the gear system to malfunction. Check if the drum bearings are in good condition or if they need to be replaced.
4. Check the pulley: The pulley may be worn out or damaged, causing the gear system to malfunction. Check if the pulley is in good condition and if it is properly aligned.

If none of these solutions work, it may be a more serious issue with the washing machine that requires professional repair. In that case, you may need to contact LG customer support or a qualified technician for assistance.

The E2 error code on an LG washing machine usually indicates a problem with the water supply. Here are some steps you can try to resolve the issue:

1. Check the water supply: Make sure that the water supply to the washing machine is turned on and the water pressure is adequate. If there is a problem with the water supply, fix it and try running the machine again.
2. Check the water inlet valve: The water inlet valve is responsible for controlling the water flow into the washing machine. If the valve is faulty, it can cause the E2 error code. To check the valve, unplug the machine and turn off the water supply. Remove the hoses from the valve and check if there is any debris or damage. If the valve is damaged, it will need to be replaced.
3. Check the water level sensor: The water level sensor is responsible for detecting the water level in the washing machine. If it is faulty, it can cause the E2 error code. To check the sensor, unplug the machine and locate the water level sensor. Check for any damage or debris and clean it. If the sensor is damaged, it will need to be replaced.

If the above steps do not resolve the issue, you may need to contact a professional for further assistance.