LG WM-1480FHD Front Load Washer - Answered Questions & Fixed issues


LG WM-1480FHD... | Answered on Apr 25, 2014 | 25 views


HAVE YOU TRIED SCENTED DRYER SHEETS

LG WM-1480FHD... | Answered on Feb 10, 2014 | 66 views


make sure it is on a cycle that takes hot water, otherwise it sounds like a hot valve fault. replacing the valve should do it.

LG WM-1480FHD... | Answered on Nov 11, 2013 | 39 views


usely a switch is on or off so I:d say no its not normal. But sounds like you know what to replace when the switch does go out, Ir its easy & very easy to replace if it anoise you

LG WM-1480FHD... | Answered on Jan 31, 2012 | 119 views


most lg front loaders have the plastic outer drums which have about 16 h/duty screws holding the two halves together. extreemly tricky to strip to gain access to inner bearing and seal. Th/stat, motor, piping and other items have to be removed and dissassembled to enable drum to be removed. that repair i suggest for a service repair.

LG WM-1480FHD... | Answered on Jan 19, 2012 | 814 views


According to the model for removing the cover varies so here is the link for instruction.you can download your particular manual (model number)Zanussi - Washing Machine user manual, operation instructions.Good luck

LG WM-1480FHD... | Answered on Sep 28, 2011 | 153 views


Well, according to the LG error look up table:

LE Locked motor error. Cause: The connector (3-pin), male,white) in the motor harness is not connected to the connector. (3-pin,female,white) of stator assembly. Or the electrical contact between the connectors. (3-pin,male,white) in the motor harness and 4-pin,female,white connector in the main PWB assembly is bad or unstable. Or the motor harness between the stator assembly and main PWB assembly is cut (open circuit) Or the hall sensor is out of order/defective.

Decoding the techno speak, this means that the little rev counter, built on to the back of the motor and connected by 3 wires has either come loose, fallen off, failed or its wires are unplugged. The result is the machine can't figure what speed the motor is running at, so it shuts it down.

LG WM-1480FHD... | Answered on Sep 16, 2011 | 153 views


CL=Children Lock
Please , release the lock by click on first two left buttons .

LG WM-1480FHD... | Answered on Apr 28, 2011 | 96 views


Yes and Yes again,you may want to visit utube .com they have videos on how to fit a Door Boot Seal.Make sure its just the seal first just in case.....

LG WM-1480FHD... | Answered on Apr 01, 2011 | 160 views


underneath......
drag maching to outside door and let old hose hang outside
this will drain alot of water out of machine then upend it to replace old hose with new 1
cheers

LG WM-1480FHD... | Answered on Mar 27, 2011 | 264 views


The problem is either there's no water in the pipelines going to the machine, the water valves are not working or stuck closed, the pressure switch is stuck in the full position, or the pressure hose is blocked. Check first and make that water is running through the inlet hoses.

Disconnect power and remove screws on the back of the top panel then pull the panel backward and upward as shown.
jahn27_236.jpg

Once the top panel is off, locate the pressure switch with a small clear hose attached to it. Detach the hose then blow air down into the hose and into the pressure switch. Also check the pressure hose for clogs or kinks and tap the pressure switch gently to free a possible stuck or welded contacts. Reattach the pressure hose then reconnect power and start the machine.

Re-disconnect power and disconnect and pressure switch wire harness if water still doesn't come in. Reconnect power and restart the machine. Replace the pressure switch if water starts to come in with the wire harness disconnected. Replace the water inlet valve if it clicks and doesn't click back right away but water still doesn't come in.

Let us know if you need further advice. Please accept the solution should you find it helpful or informative. Accepting the solution will not stop you from communicating with the expert. You can still communicate with the expert should you need further advice regarding the issue stated herein.

LG WM-1480FHD... | Answered on Mar 23, 2011 | 78 views


Hi from retired Englishman in SW France,

Sorry but this forum does not supply manuals direct; it's just made up of ordinary guys and gals, probably at home and from all over the world, with experience of addressing problems and giving guidance for free on the web ;-0)

You will need to type into your search engine/web browser '(make) washer manual' and you should be presented with a number of sources from which you can either download for free or have to pay a nominal amount. During the process you will be asked for the actual model number!

Good luck,
John C
.

LG WM-1480FHD... | Answered on Mar 12, 2011 | 34 views


(Sorry if I have answered this already!)

Hi from retired Englishman in SW France
Here are my general guidance notes on ensuring that the empty machine is 100% stable on spin.
-------------------------------------------------------------------------------------------
It is necessary to ensure absolutely that the machine, even when empty, has all 4 feet very firmly on the floor, and I mean firmly ;-0)

Doesn't matter whether it is empty or not but switch it off then-
very firmly push one front corner diagonally into the center of the machine (sorry about my UK spelling!) and see if the machine moves or rocks AT ALL, even the slightest. If it does you will need the open-ended spanner which came with the (new) machine........which of course went missing a long time ago?!! An adjustable spanner will suffice.
Adjust the foot under that corner downwards until it is very firmly- almost pushing- against the floor but not so far that the corner lifts up!
If this corner did not rock do the same to the other.
Once you cannot rock the machine the slightest little bit, screw the locking nuts up tight to the underside of the machine so that they will not move. Ideally the rear feet should also be locked.

If this has not cured the problem it is possible that the internal drum suspension is malfunctioning.

Good luck,

John C

LG WM-1480FHD... | Answered on Mar 02, 2011 | 40 views


Hi it means the childlock is on, on mine i have to press the wash and rinse buttons together and hold it till it beeps.
sharon

LG WM-1480FHD... | Answered on Feb 17, 2011 | 210 views


Hi from retired Englishman in SW France

I think 'UE' stands for 'imbalance'. Following are my general/generic instructions on balancing machines- I would start there.
----------------------------------------------------------------------------------------------------------------------------------------------

I mostly answer front load problems but ' out of balance' is a common problem with both!
So- I don't know your particular machine but the initial cure is the same.
It is necessary to ensure absolutely that the machine, even when empty, has all 4 feet very firmly on the floor, and I mean firmly ;-0)

Doesn't matter whether it is empty or not but switch it off then-
very firmly push one front corner diagonally into the centre of the machine (sorry about my UK spelling!) and see if the machine moves or rocks AT ALL, even the slightest. If it does you will need the open-ended spanner which came with the (new) machine........which of course went missing a long time ago?!! An adjustable spanner will suffice.
Adjust the foot under that corner downwards until it is very firmly- almost pushing- against the floor but not so far that the corner lifts up!
If this corner did not rock do the same to the other.
Once you cannot rock the machine the slightest little bit, screw the locking nuts up tight to the underside of the machine so that they will not move. Ideally the rear feet should also be locked.

If this has not cured the problem it is possible that the internal drum suspension is malfunctioning but I've not had any feedback of this nature.

Good luck,

John C

LG WM-1480FHD... | Answered on Feb 17, 2011 | 134 views


Follow this link for your OE error.

LG WM-1480FHD... | Answered on Dec 26, 2010 | 58 views


Go to this website. It will help you out A LOT!!!! No spam, nothing like that, but it is to help troubleshoot appliances.

http://www.repairclinic.com/Repair-Help

LG WM-1480FHD... | Answered on Nov 13, 2010 | 134 views


How many years is yoru washing machine? I suspect bthe magnet on the lid of the washer has probabkly come off which causes the washer not to identify that the door is closed. U need to replace a magnet on the lid.

LG WM-1480FHD... | Answered on Oct 17, 2010 | 225 views


LG WFT70A37ECT Top load washing machine, showing DE error... even door is close still showing this error. that is the solution... really appriciate... thanx

LG WM-1480FHD... | Answered on Oct 29, 2014 | 1,924 views

Not finding what you are looking for?
LG WM-1480FHD Front Load Washer Logo

86 questions posted

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...