Top 20 HP Hewlett Packard LaserJet 3000dn Printer Questions & Answers

Hello,
There is a problem with toner chip, the printer cannot read them corectly. Try this solutions:

Make sure you have removed the orange color notch on the left side of your cartridge, if
your cartridge is new.

Change the chip with another one.

Hi Rupert,Here's the Users Guide for your officejet.Hope this helps.Thanks!Please rate this answer.

Supply memory error is referring to a defective toner cartridge. Actually it's the electronics chip that is attached to the cartridge. The printer gets toner information by reading the chip. Replace the cartridge.

Problem with catride memory faulty,replace caetride, if its in warranty you will get replacement..

If the page looks like it is zoomed out. (Small) and everything else is normal sized, hold ctrl and press + to zoom in and ctrl and - to zoom out.

Comment back if this doesn't resolve it.

If you haven't yet, reseat the cartridges. The cartridges have a small chip on them that is read by the printer. If the chip is bad or missing, you'll get that error.Replace the toner cartridge that is causing the problem. If you just bought the cartridge return it, HP warranties them.

10.00.00 = black 10.00.01 = cyan 10.00.02 = magenta 10.00.03 = yellow

Hi Ali

Probably the printer no recognize the toner cartridge. Check the chip on toner cartridge (if have if there is an orange plastic, remove it. If not replace the toner cartridge for a new one."CB436A")

Good Luck

hi,
10.00X is the error code displayed when

• Cartridge is not installed correctly
• Use of refilled cartridges

in your case x is 0 which means that black color cartridge had a problem
problem may persist in slot holding black cartridge and /or in the cartridge

just do steps below

solution 1: check all cartridges are in right slot it is better to remove and fix it again

solution 2:
clean the surface of metal contacts with lint-free cloth
the image below will show metal contacts


solution 3: Insert the problem print cartridge into a different slot
Follow these steps to determine if the print cartridge or the slot it sits in is causing the error.

1. Open the print cartridge door completely.
2. Press the blue handle on the print cartridge drawer to release it, and then pull the drawer out completely.
3. Remove one of the non problem print cartridges from its slot.
4. Install the problem print cartridge into the empty slot.
5. Install the other print cartridge into the slot of the problem print cartridge.
6. Close the print cartridge drawer completely.
7. Close the front access door completely.

• If the error message persists , replace the problem cartridge with new one(problem is in cartridge)
• If the error message is gone , contact HP to troubleshoot a faulty slot.

regards,
cseian

• Control Panel
• Printer and Faxes
• Right click on your D1660 printer
• Select "Use Printer Online"
• Close Printer and Faxes
  

There is no Laser jet CM232v printer from HP and all laser printers have a toner cartridge, not an ink one.
Here (page 159) you can find the procedure of replacing the toner cartridge on a a multifunctional laser printer that is surely almost identical with what you have
http://h10032.www1.hp.com/ctg/Manual/c01760651.pdf

Here is the M1200 series user manual:

http://h10032.www1.hp.com/ctg/Manual/c01760651.pdf

LASERJET PROFESSIONAL M1130/M1210

Click on this link or copy and paste the complete link into your browser.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Firmware error: 1. Press CANCEL JOB to clear the print job from the printer memory. 2. Turn the printer off, and then turn the printer on. You can try reprinting the job to see if it was a temporary error. 3. If error persists, try printing a job from a different software application. If the alternate job prints, go back to the first application and try printing a different file. (If the message only appears with a certain software application or certainprint job, try upgrading the printer driver and / or firmware.) 4. If the message persists with different software applications and print jobs, disconnect all cables to the printer that connect it to the network or printer. Turn the printer off and delete the print queue. Then reboot printer AND computer, reconnect cables, and try printing again. 6. Remove all EIO devices from the printer (JetDirect cards, hard drives, etc.). If 49 error goes away, turn printer off, re-install EIO devices one at a time, and reboot printer each time to determine which EIO device is failing. 7. If printing still fails with all EIO devices removed, remove all memory DIMMs or third-party DIMMs from the printer. (Do not remove the firmware DIMM-- printer won't function without this installed.) Turn the printer on with DIMMS missing. If the error no longer exists, install each DIMM one at a time, turn printer on, test printer. Replace a DIMM if you determine that it causes the error. 8. Remember to reconnect all cables that connect the printer to the network or computer. 9. If the error persists, replace the firmware DIMM. 10. If error persists, replace the formatter.

use supplies in use error show my printer hp mf 1213 nf

MS Word cannot open scanned documents to edit. You need to run a scanned document through an OCR program (optical character recognition program) which converts the scanned document into a text document. Then you open Ms Word and import or open this text document to edit or change the text.

Check your i/o cable. Replace it with another one if possible.
Check your power cable and make sure it is connected properly.
Could also be your dc jack on your printer.

Hi need service

You can download the user manual for this unit from this link , just click HERE and proceed with the download.

This is an issue with the black toner cartridge, replace the toner

Al

Are you using HP toner? Try reseating the cartridge. If it's still getting the error, replace the cartridge.

Hi!

Download it from here!

Regards,
Pelu.