20 Most Recent ViewSonic N3735W 37 in. LCD TV - Page 4 Questions & Answers

There is a button lock in the menu of the television. Using your remote access the menu screen and unlock the buttons.

Try using a vcr dvd combo and a different input that is available on your set such as HDMI

Verify that the set is set for the correct input by pressing the source button on the remote to check if the cable is selected as the input. If not use the arrow keys to select the proper one and press OK

Hi visceran,
I am happy to help, unfortunatly your main/input board is malfunctioning, it is a problem with the processor. I had a 32' Viewsonic on my bench last week with the same symptoms.
If the tv is new you should contact Customer Service asap, also check on the return policy of the store you bought it from. Many times it is alot easier to return to the merchant than to ship to repair facility.
Let me know how it goes and if you need further assistance.
Please rate this solution. Lone99star Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/jason_77a19afa8d604dee

Buy a monitor that wil accept your video card size  resolutions? 

try codes-1608-1785-1360-1572-1618-1540.Ted10good luck

> For HD you have to have a square screen
Sorry to disagree; the standard screen has an aspect ratio of 4:3, this is far more 'square' than the 16:9 (aka 'wide screen') which is standard for HDTV. If you are on cable or satellite service, you may well have to pay extra to have the whole of your screen available for viewing.
That is why only 'over the air' broadcasts are absolutely affected by the change from analog to digital next February but other sources do not have to change over to the new standard and the 4:3 sets will work fine without any extra box until those sources decide to 'go digital.'
 

My fiance wouldnt like me answering your questions much. Just want to find a fix for my HD service. Sorry.

Try Phillips Remote Codes

10054 is the code for directv remotes. They seem to work.

it could be your flux capacitor is out. you might need to plug it in goto menus and check to see if ur runnin 21 gigawatts if not leave it plugged in and off for two days and it should refresh it

Full instructions and codes here. For what it's worth, no one buys universal remotes these days, you buy a facsimile remote which is an exact copy for the television model you have. www.remotes.com. https://universalremote.codes/viewsonic-tv/ ..

OSD Lock: Press and hold [AUTO] and the up arrow for 10 seconds. If any other buttons are pressed the message OSD Locked will display for 3 seconds. OSD Unlock: Press and hold [AUTO] and the up arrow again for 10 seconds. http://www.viewsonicglobal.com/public/products_download/user_guide/Display/VA1903A/VA1903a_UG_ENG.pdf?pass

Most likely

check power settings see if program set

The 'ON' button is not working. Pls go for a new remote.

Have a viewsonic n3246w but can't get it to tune in on dtv

First make sure that the current input Source is set to TV to see the option for scanning for channels. There is a Source button on the front of the TV. (It's on the right side as you look at the front of the TV.) The Source button on the original remote is on the left side below the number keys.There are two RF (coaxial) cable inputs near the VGA port on the back of the TV. The digital RF signal needs to go to the port above the VGA port. To scan for analog channels, press the Menu button. Then navigate to the TV setup option with the Up/Down arrows. Press OK to enter the menu. You can use either the Auto search or the Manual search. However, the Auto will be faster. You can set your country or leave it to Auto. Navigate to Start and press OK for the Auto-scan. There is a DTV menu button above the Volume + button on the remote. Use this menu and look for the Installation section to scan for channels. Again there is an Auto or Manual option. ManualsLib has the manual for the Viewsonic N3246W here: https://www.manualslib.com/manual/306714/Viewsonic-N3246w.html. See page 23 for the start of the analog TV channel scan information. See page 30 for the digital TV scan. I hope this helps. Cindy Wells (For any channel provided by a set-top box, you will not be able to use the TV to store the channel lists.)

Some Viewsonic monitors have a Power Lock feature. However, these tend to be on the monitors (like the Viewsonic VA2265Smh) with only 5 control buttons. To toggle off the power lock, press and hold the button labeled 1 (Menu/Save/Exit) and the down arrow button for 10 seconds. The N2201W TV has more buttons than that. There is no Power Lock identified in my Viewsonic TV manuals. However, you might try the press and hold Menu/Down arrow combination. I hope this helps. Cindy Wells

To toggle the OSD lock off, press the Vol + and Vol - buttons on the Viewsonic N2011 simultaneously. This is shown in the manual on page 8, see https://www.manualslib.com/manual/306712/Viewsonic-N2011.html?page=8#manual . I believe these buttons are on the back of the unit on the right hand side as you face the TV. I hope this helps. Cindy Wells