20 Most Recent Epson Stylus NX400 InkJet Printer - Page 4 Questions & Answers

Epson L210 does not support Borderless Printing. The minimum margin seems to be .1". You can see this in the Print Preview, just check the Printable Area choice on the View Tab. If you would like to use small margins around your document, use the "Printing Presets" on Epson L210, like "Document - Standard Quality". The "Document Size" will be A4. Leave this setting alone. You can still use 8-1/2 x 11 paper. Just make sure that what you're about to print will fit in the 8-1/2 x 11. My document margins were followed then. I've not tried it for 8-1/2 x 13 paper yet.

you can go to the realtek website ,type in your pc model type and get the sound drivers,,or you can go to your control panel and restore your system to before it went dumb, 2 or 3 restore points back,day before u got dat problemo,,thanks

Probably a blocked printhead.Make a simple graphic using something like PAINT.Small filled colour squares - one for each colour of cartridge your printer has.You'll soon see which part of the printhead is clogged.Make a simple Sometimes they respond to cleaning, sometimes not.

You need to clean the print head on the cartridges , please follow these steps\
# Hold the cartridge upside down, with the bar-code label facing you and take a damp paper towel.
# Use the towel to wipe the printhead of the cartridge on the bottom (where the ink comes out). Wipe the printhead horizontally in one direction only (left to right).
# Continue doing this until it looks clean.
# Then dab the cartridge on the towel to make sure the ink is flowing.
# Next, look inside the printer and locate the carrier that holds ink cartridges. Caution: Make sure the cartridges are not installed at this point.

1. Look for a shiny piece of metal underneath the contacts at the back of the carrier.
2. Take a damp cotton swab (use water only!) and wipe along the bottom of the shiny metal piece. Note: You may need more than one swab.

# Reinstall the cartridges, making sure you snap them correctly into the printer.

Start at http://www.epson.com/, select your country or region of the world, and go from there.

Don't let your ink levels drop below 25% before refilling and resetting your cartridges. There is an inner and an outer chip on these cartridges. The inner chip disables the outer chip when it's contacts are no longer bathed in ink. So, it doesn't matter if you "reset" the outer chip after refilling your empty cartridge because the chip was disabled. I'm really curious how you refilled these cartridges yourself without souring yourself on refilling from the experience. I own a Cartridge World ink refilling store and I refilled a set of these cartridges when we had replacement chips available (we don't now because our chip distributor was violating Epson patents) and it was an absolute mess, took forever, and the cartridges still didn't work in our test printer.

Inkjet printers need to be used frequently to prevent ink drying out and blocking the print head nozzles. If the print head cleaning maintenance routine does not clear the blockages, then print head needs replacing, but it may be expensive. It may be more cost effective to buy a later model and better printer than replace the print head.

Check your printer settings. Make sure you still have the proper size envelope selected. Sometimes, the settings change back to factory default when doing maintenance.

good luck i'm trying to do the same. Not working for me.

my spanish is not that good any more. mi espanol no es muy buena como era en el pasado. va a www.epson.com, a drivers and support. all-in-one or stand alone printer only? find su modelo y son pequenos papeles para lea sobre esta modelo. jacki es el mejor solucion que tengo.

Check the following:

• • If paper doesn't feed, remove it from the sheet feeder. Reload it against the right side, behind the tab, then press in the tab on the edge guide and slide it against the paper. Make sure the paper is not above the arrow mark inside the edge guide.
• • If multiple pages feed at once, remove the paper from the sheet feeder, fan the edges to separate the sheets, then reload it.
• • If the paper doesn't eject fully, you may have set the wrong paper size. Press the Stop button, then open the scanner and remove the paper. Select the correct paper size when you reprint.
• • If it's wrinkled when it ejects, the paper may be damp or too thin. Load new paper.
• • Make sure you use new, smooth, high-quality paper, that is not curled, creased, old, or too thin. Make sure to load it printable side up.
• • Do not load paper with holes punched in it for insertion in a binder.
• • Make sure you load only up to the recommended number of sheets. If you're printing on both sides of the paper, try loading fewer sheets.

Paper type

Load up to this many sheets

Plain paper

Approximately 120

Epson Bright White Paper Epson Presentation Paper Matte

80

Epson Photo Paper Glossy Epson Premium Photo Paper Glossy Epson Ultra Premium Photo Paper Glossy Epson Premium Photo Paper Semi-gloss

20

Epson Premium Presentation Paper Matte Epson Premium Presentation Paper Matte Double-Sided Epson Photo Quality Self-Adhesive Sheets Epson Iron-On Cool Peel Transfer Paper

1

• If the paper jams, do the following:

1. Gently pull any jammed paper out from the output tray or sheet feeder.

2. To eject the jammed paper, try turning the Epson Stylus NX400 off and then back on. If that doesn't work and paper is stuck inside, turn off the Epson Stylus NX400. Open the scanner, remove the jammed paper and torn pieces, close the scanner, and turn the Epson Stylus NX400 back on.