20 Most Recent
American Standard Kitchen Faucet 6310 020 White Easy Touch Pull-Out Kitchen... - Page 6 Questions & Answers
Loose single handle no brand name faucet
There is a little rubber icon Red for Hot and Blue for the cold on the front of the handle. Remove the rubber insert from the handle. There is a small allen screw that needs tighten to tighten your handle.
3/12/2013 6:13:38 PM •
American...
•
Answered
on Mar 12, 2013
Dripping water of a faucet
Hello Daniel, I've had the same problem a time or two in the past, and although it seems to be a problem you dont want to tackle, it is rather easy and dosen't take much time. First you need to know the brand name of the faucet, then go to your local hardware store and tell them what you are looking for. They should then give you a faucet repair kit that contains maybe rubber "O" rings, washers, and or gaskets, along with a diagram of how it all works. Then when you get back to your faucet, shut off your water and draing the pressure by oppening the valve (should only take a couple of seconds or so), and follow the directions on the package. Now they are small parts, so when you take it apart, just pay close attention to how it breakes down, and putting it back together will be a breeze. Hope this helped some, and best of luck
6/5/2012 5:17:35 PM •
American...
•
Answered
on Jun 05, 2012
Power flush toilet does not power flush
Usually when the power flush does not work it is because a leak has developed in the pressurized tank. They are known to develop leaks, usually along the molding lines. I am not sure if the tanks are replaceable. Or, it could be something as simple as the flush leaver not engaging the valve assembly on the tank. Take of the tank lid and try to flush and let me know what you see. Good Luck
6/4/2012 11:50:20 PM •
American...
•
Answered
on Jun 04, 2012
No hot water pressure
These types faucets have a what is called an anti scald valve build into them, it is required by law, it is either defective or out of adjustment, contact a local hardware store for more detailed info.
2/2/2012 7:55:33 PM •
American...
•
Answered
on Feb 02, 2012
How to replace sensor of z6915
http://www.zurn.com/pages/catalog.asp?ProductGroupID=185&OperationID=22#p4179From that page, locate the model and the drop down selector for the installation instructions (#2) will have the blow up diagram of the unit.It appears the only way they handle the sensor is as part of the spout assembly. P6915-1This may be a longshot, but it "may" be possible to clean up the sensor so it is functional again. If you use the same approach as you would do in paint finishing, start with 400 grit to smooth it, drop to 800 then 1500 grit, then rub it down with fine cut polish and then fine cut cleaner, I have used this method to remove scratched in grafitti on clear acrylic plastic with excellent results and no crazing later. The finishing compounds are Maguire's paint finishing, but comparable 3M products or other brands should work. It may seem like a great deal of work, but in the long run when you weigh the number of faucets and what the spout price is versus the time/overhead of the polishing, it may be cost effective if enough units are involved. You know the new ones will get scratched up again.
1/16/2012 6:10:42 AM •
American...
•
Answered
on Jan 16, 2012
I have an American Standard
pull it out as far as you need. You will not hurt anything just dont try to wash the car its not that long
I have my spout in the middle and I pull out all I need to clean out both sidees it works just fine
Thanks Richard
9/7/2011 1:49:41 PM •
American...
•
Answered
on Sep 07, 2011
Water leaks down to the
Ok more than likly your putty dried out and yes you will have to remove the drain and do it again. First you need to get a small tub of putty, you dont need much. If your drain has a cross in the drain when you look in the bottom you would need to buy what is call a "*********" this is a tool that fits into the drain and then you would turn the ********* counter clock wise. You will more than likey have to use a an other tool to add some extra power to turn the *********.
After you get that out clean all the old puddy out and then screw in back in the same way it came out and test it by filling the tub
Thanks Tom
9/7/2011 12:59:02 PM •
American...
•
Answered
on Sep 07, 2011
When I turn on the
Does it have a diverter on the spout? If so, replace the spout with the same type. If it is a new installation, did you make up the valve or was it complete and designed for tub & shower? If it's an old valve and it has a separate diverter stem, there is a spacer behind the valve between the valve housing. Replace it.
4/22/2011 2:07:06 AM •
American...
•
Answered
on Apr 22, 2011
Looking for faucet repair parts for early 1973's
You will need to take those old parts to a store or place that handles Danco replacement parts. I wish I could direct you to a place that would have what your looking for but parts that old are just not out there. The other
possibility is to rebuild what you have those old parts a really tough. I have some old stems and handles that you are welcome to just send me some pictures of what you have and we might get lucky.
[email protected]
3/20/2011 11:02:47 PM •
American...
•
Answered
on Mar 20, 2011
I'm making a concrete porch, do I need to lay a
If you live in an area where it freezes for long periods of time in the winter you should put in footers at a 3 to 4 feet and even if you don't live in freeze area you should put in footers at a 1 1/2 to two feet if want the porch, As for the 3" you may as well go with what ever a 2x4 comes to and you will not have to cut the boards dow to 3".
3/14/2011 3:04:26 AM •
American...
•
Answered
on Mar 14, 2011
How to remove the corroded valve seat housing in my tub faucet
Some seats ae rremovable and some or not Some take a hex(allen) wrench and some take a square (seat removal tool) Most of us use a seat grinder. (another tool to dress up the seat (Remove material) past the seat damage. You will find any of these tools at any hardware store that sells plumbing parts. If the seats have a square or hex hole remove and replace rather that grind(dress)the seat. All right hand threads meaning turn counter clock wise to remove. Take old seat to the American Standard plmbing supply outlet and then will match it up. Good fix-in to ya.
3/6/2011 6:24:15 AM •
American...
•
Answered
on Mar 06, 2011
How to calculate the weihgt of circular cones
(1/3) x pi x radius2 x height x density = pounds
where ::
radius = radius of base in inches
density = pounds per cubic inch
height = height in inches
(or you could use feet, meters, cm, mm for radius & height and use kg for density or wahtever units you wish as long as the units are consistent)
Charlie
2/22/2011 4:56:40 AM •
American...
•
Answered
on Feb 22, 2011
Dcasd
bdujwu7ye je9809 l,ldchr fk;lkjf
2/11/2011 2:27:25 AM •
American...
•
Answered
on Feb 11, 2011
My gadget is not opening
Unscrew the pop-up cable connector from the drain tail-piece and rotate the screw on the side 180 degrees. Reattach the cable adapter.
12/23/2010 11:39:26 PM •
American...
•
Answered
on Dec 23, 2010
Not finding what you are looking for?