Top 20
Lisle Serpentine Belt Tool & Accessories - Expanded Model Questions & Answers
My serpentine belt broke while driving a 1995 ford escort the car died is this normal
You should be able to replace the belt and be running again. If you ran the engine for a long time or high RPM without the belt, you may have overheated it and caused additional problems - but you'd probably gotten a high temperature warning light if that were the case. The serpentine belt provides a way to transfer mechanical energy from the engine to the alternator, power steering pump, A/C condenser, smog pump, water pump, etc. Once that belt breaks - all of these devices cease to function (even though the engine is still running) and will cause the engine to stop eventually. If you broke a timing belt - that would be a different story - if the engine is an "interference" or a "zero tolerance" type. The valves inside the engine would be crushed by the pistons immediately - rendering the engine in need of some very expensive repairs or complete replacement. Timing belts generally need to be replaced every 50,000 - 60,000 miles (or 5 years - whichever happens first or as outlined in your owner's manual). Engines with timing chains do not require replacement as a regular maintenance item.Good luck!
I'm trying to put a serpentine belt on a97 buick
there will be a diagram on the radaitor support, or on the hood next to the latch, you will need a wrench to turn the belt tensioner so it will loosen up enought to get the old belt off and the new one on, you have to hold it so you can get the belt off and on.
No room under hood to change serpentine belt
Click on the following free direct
Link. It has the correct Serpentine Belt Diagrams for your 1998 Pontiac Grand AM depending on your 2.7L Engine Options (AC/No AC etc.).
Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!
http://www.2carpros.com/car_repair_information/year/1998/make/pontiac/model/grand_am/1998_pontiac_grand_am_drive_belt_routing_diagram.htm"HOW TO":
Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.
Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them
When do i need to change my serpentine belt
Look at the grooved side of the belt and replace when you see lots of stress cracks throughout the belt. Also, if any strands are whipping around on the front side--replace
Not finding what you are looking for?