York Yankees Bedding MLB Comforter - Answered Questions & Fixed issues


Hi try jumping out the pressure switch see if it lights and check th rair filter might need a clean

York Yankees... | Answered on Nov 13, 2015 | 3,350 views


try a search for the error on Google

York Yankees... | Answered on May 30, 2015 | 202 views


Call York at 1-800-361-0448 or 1-905-827-6362. I believe they have all instruction books for all of their home gyms.

York Yankees... | Answered on Jun 08, 2017 | 13,206 views


how do i put the gym together without instructions

York Yankees... | Answered on Nov 01, 2011 | 1,359 views


ONCE YOU HAVE SET JUST PRESS START

York Yankees... | Answered on Oct 18, 2011 | 149 views


My chiller was high pressure trip and i cannot reset the fault using 9675 and 1380 passcode! What should i do ?

York Yankees... | Answered on Jul 29, 2011 | 248 views


Click the link below:--
http://technoanswers.blogspot.com/2011/06/error-3-on-luxaire-heatpump.html ---------
This should help.Thanks.Helpmech.

York Yankees... | Answered on Jun 11, 2011 | 151 views


hi , i have most manuals what is it you need to know
please email me on x.celfitness@live.com
and i can send you the manual

Kind Regards
Joe

York Yankees... | Answered on Apr 07, 2011 | 441 views


Low suction pressure normally , happens when the system go low in refrigrant . but some times it happens if on of your drain or feed valves malfunction , cause of a mechanical or electrical problem with one of the valves. or error , that you read on the display the valve is open ...percent . but realy it is not.

York Yankees... | Answered on Jul 20, 2017 | 1,947 views


Hi,
I assume you are talking about a York furnace????
Are you talking inducer blower or furnace blower that moves the air through the furnace...?

Here is a tip that will help you to get better results from your question on Fixya.


How to ask a question on FixYa

heatman101

York Yankees... | Answered on Jan 30, 2011 | 105 views


You will probably have to go with a "generic" gas valve. Try contacting Grainger to see if they can cross reference a workable solution.

York Yankees... | Answered on Jan 15, 2011 | 255 views


Probably the flame sensor is dirty. Should be wire protruding into flames opposite end of flame tubes from igniter. Clean with steel wool.

York Yankees... | Answered on Nov 13, 2015 | 847 views


search youtube or google for installation instructions.

York Yankees... | Answered on Jan 03, 2011 | 751 views


Hi,
Without actually being able to get gauges on there to check it out.... I would say that you have a leak and that you have a system that is low on charge....
I would get a tech to get gauges on there and see exactly what is happening...

heatman101

York Yankees... | Answered on Jan 02, 2011 | 29 views


How the cable on Home gym4180 runs thru pullies

York Yankees... | Answered on Dec 27, 2010 | 5,384 views


You can obtain the manual from York fitness (email support) or I can email it to you

York Yankees... | Answered on Jun 20, 2015 | 737 views


Follow these steps to install the heatpump :
•1
Choose a location for the outside part of your heat pump and place it about 10 inches from the wall of your home. Ensure that you face the heat pump with the connections toward the wall. Leave at least 18 inches for service access at the back corner of the unit and keep the top 36 inches away from anything that can block the air vents.
•2
Place your heat pump on a 4-inch slab of concrete that isn't connected to your home. Ensure that you make the slab level and surround it with gravel so you don't have problems with drainage from the heat pump. Leave a clearance of 3 inches from the coil at the bottom of the heat pump for proper drainage of frost buildup.
•3
Mount the inside unit, or air handler, inside your home. If you install the two parts and separate them by a distance greater than 15 feet, you must ensure that you don't lift the liquid and suction lines too high.
•4
Insulate the vapor gas line of your heat pump with 1/2-inch-thick insulation around the tubing, making sure to insulate the entire length of the tubing. Cover the end of the tubing that you start with so you don't let any debris into the tubing.
•5
Connect the outdoor unit of your heat pump to the indoor unit. Ensure that the copper tubing is round at the end you connect. Take off the valve cap on the outside unit and keep the cap clean. Open the valve body with an Allen wrench, insert the copper tubing and replace the valve cap. Use a wrench to tighten the valve cap and seal it into place.
•6
Allow a slow, steady release of pressure from the indoor coil when you perforate the copper caps. Secure the tubing to the indoor unit to keep the coil dry. If you leave the coil uncovered, you risk exposure to moisture.

York Yankees... | Answered on Oct 25, 2010 | 229 views


Your problem might be that a magnet has fallen off. Here's an illustrated guide that will make fixing it easy: http://fixmytreadmill.blogspot.com/2010/10/how-to-fix-treadmill-e1-error.html

Good luck.

York Yankees... | Answered on May 29, 2011 | 2,506 views


There is a small idling mixture screw on the side of the carburettor.
As the engine is not well suited to the carb. it mainly runs on the idle setting!
As long as you are not leaving the choke on. This is a little tab on the top of the carb. You start with it set on C then soon set it on the middle position, and after about 3 mins turn it off.

York Yankees... | Answered on Oct 03, 2010 | 2,432 views


replace the drive belt

York Yankees... | Answered on Aug 13, 2010 | 101 views

Not finding what you are looking for?
York Yankees Bedding MLB Comforter Logo

207 questions posted

Ask a Question

Usually answered in minutes!

Top York Sport & Outdoor - Others Experts

Paul Carew

Level 3 Expert

3484 Answers

ray gallant

Level 3 Expert

66213 Answers

Chris Walker
Chris Walker

Level 3 Expert

1533 Answers

Are you a York Sport and Outdoor - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...