York Yankees Bedding MLB Comforter - Page 3 - Answered Questions & Fixed issues
I got a E1 appears on my york 60100 and it's not working at all
the E1 error with yorks typically means that the speed sensor isnt communication correctly with the computer. Here is the series to try and get things communicating again.
Turn off and on a couple times.
No luck...
Turn off and use your feet to rotate the running mat once around. Turn back on.
No luck...
Turn off and unplug. Check all wires to make sure nothing is unplugged inside or on the machine other than the main power plug. I would also just for good measure unplug and plug all wires I can easily reach and do so with. Once everything is buttoned safely back up plug the machine back in and turn on.
6/3/2009 6:07:17 PM •
York Yankees...
•
Answered
on Jun 03, 2009
•
1,336 views
Replacement of control board
united products, rosedale, md. shut off power and write down all of the low voltage connections, double check everything before you restore power
2/21/2009 11:27:47 PM •
York Yankees...
•
Answered
on Feb 21, 2009
•
366 views
Speed problem
There is a rotating handle to the right of the display panel that you need to turn clockwise to slow down and anitclockwise to speed up, this is the only speed control. Turn it all the way and it will start at the slowest speed about 4kph. Good luck
6/13/2011 8:08:05 AM •
York Yankees...
•
Answered
on Jun 13, 2011
•
420 views
Heyy, Are you perhaps a
S10000AFC is just a capacitor. D6879847 CAPACITOR-ROUND (M11, M12, M16, M17) is a listing at Johnstone Jupply.
1/2/2009 7:18:56 PM •
York Yankees...
•
Answered
on Jan 02, 2009
•
130 views
Failed electrical part
S10000AFC is just a capacitor.
D6879847 CAPACITOR-ROUND (M11, M12, M16, M17) is a listing at Jonstone Jupply.
1/2/2009 7:05:02 PM •
York Yankees...
•
Answered
on Jan 02, 2009
•
340 views
York high effenciency furnace not firing all the time
has anyone worked on this furnace because the error would indicate that the positive 120 volt and the neg 120 volt is swapped , these units will also do this when the ground wire to the furnace or gas valve or furnace or @ the panel is lose , corroded , or missing , the gnd must be present to open valve , I am aware that ac is is not usually polarity sensitive but in this case it most certainly is ...have seen many time and know it to be true
4/17/2015 10:41:47 PM •
York Yankees...
•
Answered
on Apr 17, 2015
•
1,113 views
Owners Manual
York Corporate Headquarters
631 South Richland Ave.
York, PA 17403
Phone: (717) 771-7890
Contacting York
Mail:
York International Corp.
P.O. Box 1592
York, PA 17405-1592
USA
Phone: (877) 874-7378
York WebsiteYork was purchased by Johnson Controls in 2005
Johnson Website.I cannot find an actual manual online. I hope this information helps you. Good Luck.
5/12/2015 7:48:31 PM •
York Yankees...
•
Answered
on May 12, 2015
•
3,662 views
Heat pump wiring
yes i can , you need to hookup the r and the o together so that the reversing vvalvce is allways energized . so with that im mind send r,y,c,o to theout side unit. at the ahu you'll hook up the 5 wires for the furnace, r g w1 w2 com and at the thermostat r,w1,w2,y,g,com,o then you will be set (the o get hooked up to o and goes straight out side.
12/25/2008 6:05:48 AM •
York Yankees...
•
Answered
on Dec 25, 2008
•
1,072 views
Not finding what you are looking for?