Top 20
Bowflex Treadmill Series 7 Questions & Answers
Avanti 928 Treadmill U8 error
try to LUBE the deck belt, with silicones or wax, . If the problem persist TIME to replace the old deck board.However, adjust The REED switch + speed sensor.. See the owner manual for to locatea. otherwise download free from
www.fitnessmanualsonline.comGod bless you
5/20/2013 12:26:26 PM •
Bowflex...
•
336 views • 0 helpful votes
My Bowman treadmill 7 series
Make sure the magnetic safety key ('safety pull' or 'emergency stop magnet') is in place. SAFE OUT indicates that the safety key is not in position or is otherwise not working properly.
For more information consult the following manuals:
http://download.dfxi.com/supportdocs/OM/Bowflex/BFX_TM3-5-7_OM_RevD_web.pdf
http://www.pdfstock.com/bowflex-3-5-7-series-treadmills-assembly-manual-pdf.html
5/5/2011 11:08:28 PM •
Bowflex...
•
930 views • 2 helpful votes
I have a freespirit treadmill
ok, this is hard for me to explain because i dont know the proper terms for everything but i will try...so plz bare with me...I will start with the sides that you stand on to take a breather (at least i do)...follow them back to where they end...there should be a hole in each one where a wrench will fit, its prolly an allen key that u have to use (it is for ours), insert the right size tool in the hole and with ur speed set on approx 3.5 little by little turn the key while the belt makes some revolutions, you will know which way to turn it when you watch ur belt move, then basically it is a trial and error thing. when ur belt is back to correct position just stop...ur done!!
1/31/2011 4:09:33 PM •
Bowflex...
•
559 views • 2 helpful votes
Haven't used the treadmill for
Hi,
This is a very common problem with Bowflex.The belt gets stretched out a lot.So the belt rubs and makes noise.Call bowflex directly and ask Call (800)
667-1689. They probably have service centers located near you.Ask them
for new belt and if you have warranty you can claim it.Dont open the treadmill you will void warranty.
Please do rate the solution if the issue is resolved or post a comment for further assistance.
Thank you for using fixya have a nice day:-)
2/20/2011 1:44:03 AM •
Bowflex...
•
223 views • 1 helpful votes
The treadmill powers up but
I HAVE WESLO CADENCE M 5 MODEL NO. WETL12706.0 IT POWERS UP BUT DOES NOT MOVE ANY HELP PLEASE
12/16/2010 10:33:06 PM •
Bowflex...
•
305 views • 3 helpful votes
I have an L5 error on the display. Belt not
This is a LS or speed sensor error, it can be caused by a belt that is too tight, non lubricated walking belt and or a bad sensor. If the belt does not move at all, Bowflex will tell you to buy a new lower control board. $227 direct from them (Nautilus)
7/19/2010 3:08:05 PM •
Bowflex...
•
2,214 views • 6 helpful votes
Shows "safe out" but the
I had the same problem, however the
treadmill
remained in 'safe out' status even when the Safety pull pin was
correctly inserted.
The cause of my fault was that one of the kids
decided to insert a wrist watch into the round hole located on the
control panel's lower cover. In doing so this unplugged the cable connector for the magnetic switch which operates the 'safe out' function,
from the main circuit board. The
repair was quick and easy, i turned the power off, removed the bottom
cover from the control panel and simply plugged the magnetic switch back
into the main circuit board and all was back to normal.
4/14/2010 2:39:08 AM •
Bowflex...
•
416 views • 0 helpful votes
Power cuts out when turned on
Circuit breaker (house) or treadmill power? Display, treadmill or both? Not much hope for you if you can't try a little to help yourself.
3/7/2010 8:51:36 PM •
Bowflex...
•
442 views • 0 helpful votes
Safe out
Hi,
The treadmill remained in 'safe out' status even when the Safety pull pin was correctly inserted.
The cause of my fault was that one of the kids decided to insert a wrist watch into the round hole located on the control panel's lower cover. In doing so this unplugged the cable conector for the magnetic switch which operates the 'safe out' function, from the main circuit board. The repair was quick and easy, i turned the power off, removed the bottom cover from the control panel and simply plugged the magnetic switch back into the main circuit board and all was back to normal.
Thanks,
Save Tree.
4/14/2010 2:54:05 AM •
Bowflex...
•
77 views • 0 helpful votes
Not finding what you are looking for?