Kettler Mondeo Elliptical Trainer - Answered Questions & Fixed issues


Try unplugging for 5 mins plug back in might reset .

Kettler Mondeo... | Answered on Jan 23, 2018 | 294 views


You can get the manual for the computer part from here

http://www.infinitidirect.com.au/manuals/E6700_COMPUTER.pdf

Kettler Mondeo... | Answered on Aug 06, 2014 | 673 views


if there's any instructions, read them

Kettler Mondeo... | Answered on Feb 19, 2014 | 250 views


I need a new computer for my Kettler Corsa St 2700-7 Bike C/R 1:8
Were can I order it?

Kettler Mondeo... | Answered on Dec 29, 2013 | 271 views


Is there a regulator for pedal pressure

Kettler Mondeo... | Answered on Oct 31, 2018 | 928 views


E-2 ERROR COULD BE A POORLY FITTING CONNECTOR - SEE MY POST FOR MORE INFO

Kettler Mondeo... | Answered on Jul 19, 2011 | 1,445 views


E-2 FAULTS ARE PROBABLY DUE TO A FAULTY CONNECTION BETWEEN THE CONNECTING PLUGS-MINE WAS,I CHANGED A LEAD IN THE END AND SOLVED THE PROBLEM.PLEASE SEE MY POST ON THIS SITE ON THIS MATTER. MARK DAVIES

Kettler Mondeo... | Answered on Jul 19, 2011 | 1,780 views


Welcome to FixYa.

To do a full RESET, turn the device on then press and hold the SET key until a full display will be shown like the image below.
jas247_63.png

Thank you for using Fixya. Have a great day.

Jas247

Kettler Mondeo... | Answered on Jul 12, 2011 | 280 views


Contact Kettler as per the following instructions from their website: https://www.kettlerusa.com/parts. Your product is still available on the Canadian site so you should be able to order parts.

KETTLER'S Parts and Service Staff are available Monday thru Friday from 9:00 a.m. to 4:30 p.m. EST.

Requests can be submitted by phone to 866.804.0440, fax to 757.563.9273 or e-mail to parts@kettlerusa.com.

Model number of your product, your name, phone number or e-mail address is extremely important in order to process your order on time. Regular orders should be completed within 4-5 business days of order receipt. Special orders (parts required to be shipped from manufacturer in Germany) should be completed within 30 - 90 days. Our phone system is equipped to process messages in the order they were received.

Please only submit your request once by phone, fax or e-mail. Each of our KETTLER Parts and Service staff will provide you with accuracy, excellence and friendly professionalism. Please note we are only able to service US and CANADIAN customers.

To look up the part numbers for the items you require and for future reference your manual is available here:

https://www.kettlerusa.com/manuals/fitness/crosstrainers/7852-690.pdf

Kettler Mondeo... | Answered on Jun 25, 2011 | 149 views


I have a kettler derby exercise bike, but inside no case battery only display ,do i need to buy a new display ?

Kettler Mondeo... | Answered on Jun 16, 2011 | 1,090 views


If you look behind the unit, (directly behind the digital readout) you'll see a small rectangular inset, if you look up in that (I used my cell phone light), you'll see a tab that you can pry with a screwdriver gently to release the computer section. Just keep one hand on top, when you pry it you'll feel the unit pop up, then you can lift it out. It takes 2 AA batteries, thankfully not some bizarre disk batteries :)
Btw when you look at the readout, you'll notice it's set in a silver square- that square is the computer module that pops out.
Hope this helps!

Kettler Mondeo... | Answered on Feb 21, 2011 | 1,739 views


This is a common problem for the CTR1, it actually sounds a lot worse than it is. It's just one of the 4 bolts that hold the front "pole" of the CTR1 in place that is broken. You will need to unscrew the bolts at the base (just move the plastic piece that hides the bolts up on the "pole"). After removing the pole you will need to remove the broken bolt from the inside of the "pole" with plyers. Then just put the pole back in the base, replace the screws (be sure to tighten them good). All will be good :)

This is a weak point of the CTR1, be prepared to run into the same problem again down the road...

Kettler Mondeo... | Answered on Aug 08, 2011 | 1,739 views


go to this web site http://www.kettlerusa.com/Manuals/Fitness%20Computer/Mondeo.pdf

Kettler Mondeo... | Answered on Nov 18, 2010 | 1,378 views


Manuals for Kettler products currently selling in the US can be found at this link http://www.kettlerusa.com/page5.html

Kettler Mondeo... | Answered on Oct 08, 2010 | 1,515 views


It could be that the motor is no longer functioning. This is usually caused by power surges to the outlet. Contact Kettler for assistance. Listing for Kettler worldwide is found at www.kettler.net under global.

Kettler Mondeo... | Answered on Oct 08, 2010 | 1,097 views


The 3 year warranty details can be found at http://www.kettlerusa.com/KETTLER%20warranty.pdf
It appears to cover manufacturer's defects only

Kettler Mondeo... | Answered on Oct 08, 2010 | 146 views


Go to www.kettler.net click on global for contact information world wide for Kettler.

Kettler Mondeo... | Answered on Oct 08, 2010 | 262 views


Go to www.kettler.net look for global, click on global and it gives you a listing for Kettler distrubutors world wide who should be able to help you.

Kettler Mondeo... | Answered on Oct 08, 2010 | 349 views


You can get the manual on the link below.

http://www.kettlerusa.com/CTR1.pdf

Good Luck and please rate

Kettler Mondeo... | Answered on Jun 13, 2010 | 3,987 views

Not finding what you are looking for?
Kettler Mondeo Elliptical Trainer Logo

164 questions posted

Ask a Question

Usually answered in minutes!

Top Kettler Sport & Outdoor - Others Experts

Marvin
Marvin

Level 3 Expert

85219 Answers

Brad Brown

Level 3 Expert

18134 Answers

Tom Chichester

Level 3 Expert

55370 Answers

Are you a Kettler Sport and Outdoor - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...