Kyocera FS-1118 Printer - Answered Questions & Fixed issues


scanner unit dusty please clean than solve problem

Kyocera FS-1118... | Answered on Sep 10, 2016 | 60 views


Calling a service person might lead to correction.

Kyocera FS-1118... | Answered on Aug 27, 2016 | 263 views


my dear you clean CCD camera and mirror

Kyocera FS-1118... | Answered on Mar 29, 2018 | 215 views


you chek heater unit and fouse

Kyocera FS-1118... | Answered on Jul 08, 2015 | 73 views


Check the toner sensor under the processing unit (PU).
Remove the PU and you will see in the front left side, inside the machine, a black sensor (a black part with cross screw on it and a spring underneath it. There is a possibility that sensor to be dirty or damaged.
An important question is... is the toner original or compatible with appropriate chip (toner id)?

Kyocera FS-1118... | Answered on Jun 03, 2014 | 85 views


If the code is C6400, then just follow the procedure showing in the images below.
If the code is C6000, then you have to remove the fuser unit and check the thermistor, the thermal cut out and the heater lamp. If are able to fix the problem-damage, then follow the procedure below to reset the service call.
b6abe89e-6db1-403f-b1d5-10039126b726.jpg 6bbf89df-5e1f-4ba9-830e-5fa3e278ce55.jpg

Kyocera FS-1118... | Answered on Jun 03, 2014 | 165 views


1-4-1 Maintenance mode
The machine is equipped with a maintenance function which can be used to maintain and service the machine.
(1) Executing a maintenance item
Select Service setting using
the up/down cursor keys.
The selected maintenance item is run.
Press the back key.
Press the enter key.
Start
End
The maintenance item is
selected.
Maintenance mode is exited.
Maintenance mode is entered.
Repeat the same
maintenance item?
Run another maintenance
item?
Turning power switch off and back on
No
No
Yes
Yes
Select Maintenance mode using
the up/down cursor keys.
Enter the maintenance item
number using the up/down keys.
While pressing the start key and the # key,
press the enter key.
Press the system menu/counter key.
Press the enter key.
* The test print mode cannot be stopped until the preset number of sheets is printed. To stop the operation, remove the
cassette to cause a paper empty state. To terminate the test print mode in the middle of operation, you must turn off the
power switch and then on again to exit the maintenanc
when in maintenance mode go to 163 to reset

Kyocera FS-1118... | Answered on May 09, 2014 | 220 views


Works with ERROR C6000, C6300, C6400

Switch off
Open Toner Cover
Switch on, holding "System Menu"
Go to "Secure Setting"
"Enter"
Hold "Start" "#" "Enter"
Scoll down to "Maintenance Mode"
"Enter"
Scoll down to "U163"
Scoll do "Execute"
"Enter"
Close Toner Cover
Leave run for a few seconds
Switch off
Switch on....

I’m happy to help further over the phone at https://www.6ya.com/expert/ron_9356d26241d4cbf7

Kyocera FS-1118... | Answered on May 04, 2014 | 901 views


replace the fuser will fix that. Or if you want to stip it down check the lamps and if their ok change the thermistor and thermostat. But your better off just replacing the whole unit

I’m happy to help further over the phone at https://www.6ya.com/expert/ron_9356d26241d4cbf7

Kyocera FS-1118... | Answered on May 04, 2014 | 806 views


It means the exposure lamp is not turned on. Either a connector has come loose or the exposure lamp and/or the inverter pwb and/or the control pwb must be replaced

Kyocera FS-1118... | Answered on Jun 11, 2014 | 165 views


bad power supply

Kyocera FS-1118... | Answered on Dec 26, 2013 | 36 views


Zero-cross signal error,While fuser heater ON/OFF control is performed, the zero-cross signal is not input within 3 s. The problem is; Defective PWB, replace the engine PWB or power source PWB and check for correct operation.

Kyocera FS-1118... | Answered on Jun 10, 2013 | 119 views


Hello try to download a user manual:

http://www.kyoceradocumentsolutions.eu/index/service/dlc.false.driver.FS1118MFP._.EN.html#

Or contact your local dealer.

Kyocera FS-1118... | Answered on Nov 12, 2012 | 107 views


Apparently there is a communication error between the printer mail server. Can you ping both reliably ? Is it an internal mail server ? If yes, can you ping the printer from it ? Did you try changing the network cable ? How about IP addresses ? Could there be a conflict ?
Cheers,
Franck Horlaville TAM Software

Kyocera FS-1118... | Answered on Sep 13, 2011 | 831 views

Not finding what you are looking for?
Kyocera FS-1118 Printer Logo

59 questions posted

Ask a Question

Usually answered in minutes!

Top Kyocera Office Equipment & Supplies Experts

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Are you a Kyocera Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...